Introduzione

The guide takes place from the Camera Lens Assembly guide.

Parti

Nessuna parte richiesta.

  1. Locate the memory card and battery card latch on the bottom of the camera.
    • Locate the memory card and battery card latch on the bottom of the camera.

    • Slide the latch to the open position.

    Aggiungi Commento

  2. Open the battery latch, and slide the battery release lever to the right.
    • Open the battery latch, and slide the battery release lever to the right.

    Aggiungi Commento

    • Remove the battery from the camera.

    Aggiungi Commento

    • Using a size #00 Phillips screwdriver, remove the three 4.58 mm screws on the bottom of the camera.

    • Use this screwdriver for all screws in the device.

    Aggiungi Commento

    • Remove the 3.15 mm screw on the left side of the camera.

    Aggiungi Commento

    • Remove the left side casing.

    Aggiungi Commento

    • Remove the two 3.15 mm screws on the right side of the camera.

    Aggiungi Commento

    • Remove the bottom right panel.

    Aggiungi Commento

  3. Spedizione gratuita per ordini superiori a $20
    Usa il codice BLUEANDBLACK al checkout
    Spedizione gratuita per ordini superiori a $20
    Usa il codice BLUEANDBLACK
    • Gently remove the back casing.

    • Start at the bottom and carefully pry towards the top to get this piece free.

    Aggiungi Commento

    • Remove the two black 5.35 mm screws that hold in the front faceplate.

    • There may be a third screw the the right of the lens assembly.

    Aggiungi Commento

    • Carefully remove the upper assembly, which houses the buttons and the flash battery.

    Aggiungi Commento

    • Carefully remove the front casing after verifying that the thin plastic around the lens is not still attached.

    Aggiungi Commento

    • Remove the three black 5mm screws attached to the lens frame.

    Aggiungi Commento

    • Remove the lens frame.

    Aggiungi Commento

    • Lift out the circuit board as shown.

    Aggiungi Commento

    • Lift the two black latches that hold the connector ribbons in place.

    • Disconnect the two ribbons.

    Aggiungi Commento

    • Remove the lens assembly as shown.

    Aggiungi Commento

    • Remove four 4mm screws from the lens assembly.

    Aggiungi Commento

    • Carefully turn over the assembly.

    Aggiungi Commento

    • Remove the Fixed Frame Unit by separating it from the assembly.

    • Remove the Direct Frame Unit from the assembly.

    Aggiungi Commento

    • Remove the 1st lens frame from the lens assembly.

    Aggiungi Commento

    • Detach the 2nd Frame Unit from the assembly.

    Aggiungi Commento

    • Remove the 4mm screw from the lens housing.

    Aggiungi Commento

    • Separate the lens housing.

    • Replace the lens by gently prying away from the assembly.

    Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 4 persone hanno completato questa guida.

Caleb Fink

Membro da: 11/10/2010

186 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 9-22, Regan Fall 2010 Membro di Cal Poly, Team 9-22, Regan Fall 2010

CPSU-REGAN-F10S9G22

4 Membri

8 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 14

Tutti i Tempi: 11,912