Aggiusta la tua roba Comunità Store

iRobot Roomba 890 Charging Contacts Replacement

Cosa ti serve

  1. iRobot Roomba 890 Charging Contacts Replacement, Charging Contacts: passo 1, immagine 1 di 2 iRobot Roomba 890 Charging Contacts Replacement, Charging Contacts: passo 1, immagine 2 di 2

    • Use a Phillips #2 screwdriver to remove the 7.7 mm screw.

    • Remove the yellow brush head.

    Modifica

  2. iRobot Roomba 890 Charging Contacts Replacement: passo 2, immagine 1 di 1

    • Place the Roomba facedown, with its bottom facing you.

    • Use a Phillips #2 screwdriver to remove the two 11 mm screws.

    Modifica

  3. iRobot Roomba 890 Charging Contacts Replacement: passo 3, immagine 1 di 1

    • Remove the battery plate.

    • Remove the battery by pulling directly up on the grey pull tabs.

    Modifica

  4. iRobot Roomba 890 Charging Contacts Replacement: passo 4, immagine 1 di 2 iRobot Roomba 890 Charging Contacts Replacement: passo 4, immagine 2 di 2

    • Use a Phillips #2 screwdriver to remove the four 11 mm screws.

    • Remove the bottom plate of the Roomba.

    Modifica

  6. iRobot Roomba 890 Charging Contacts Replacement: passo 5, immagine 1 di 2 iRobot Roomba 890 Charging Contacts Replacement: passo 5, immagine 2 di 2

    • Turn Roomba face up.

    • Remove the dustbin by pressing the release button on the top side of the Roomba and pulling it straight out.

    Modifica

  7. iRobot Roomba 890 Charging Contacts Replacement: passo 6, immagine 1 di 2 iRobot Roomba 890 Charging Contacts Replacement: passo 6, immagine 2 di 2

    • Using the opening tool, remove retaining band.

    • Use the removal tool to remove the face plate as well.

    • Pry up slowly around the edges to prevent damage to the plastic components.

    Modifica

  8. iRobot Roomba 890 Charging Contacts Replacement: passo 7, immagine 1 di 3 iRobot Roomba 890 Charging Contacts Replacement: passo 7, immagine 2 di 3 iRobot Roomba 890 Charging Contacts Replacement: passo 7, immagine 3 di 3

    • Use a Phillips #1 screwdriver to remove the two 9.5 mm handle screws.

    • Use a Phillips #1 screwdriver to remove the fourteen 9.5 mm top plate screws.

    • Lift the top plate off.

    Modifica

  9. iRobot Roomba 890 Charging Contacts Replacement: passo 8, immagine 1 di 2 iRobot Roomba 890 Charging Contacts Replacement: passo 8, immagine 2 di 2

    • Locate the charging contact wire connection to the motherboard.

    • Release the connector.

    • Pull gently on the white plug, not the wires themselves.

    Modifica

  10. iRobot Roomba 890 Charging Contacts Replacement: passo 9, immagine 1 di 1

    • Use a Phillips #1 screwdriver to remove the four 9.3 mm bumper sensor screws.

    Modifica

  11. iRobot Roomba 890 Charging Contacts Replacement: passo 10, immagine 1 di 1

    • Use a Phillips #1 screwdriver to remove the two 9.3 mm screws holding the charging contact backings in place.

    • Remove the charging contact backings.

    Modifica

  12. iRobot Roomba 890 Charging Contacts Replacement: passo 11, immagine 1 di 1

    • Use the iFixit opening tool to gently pry down on the charging contact, on the side closest to the cliff sensor.

    • With the charging contact dislodged, pull it through the Roomba housing.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Autore

con 1 altro collaboratore

Devin Steiblin

Membro da: 03/28/22

442 Reputazione

2 Guide realizzate

Distintivi: 6

+3 altri distintivi

Team

UMass Dartmouth, Team 1-3, Petersen Spring 2022 Membro di UMass Dartmouth, Team 1-3, Petersen Spring 2022

UMASSD-PETERSEN-S22S1G3

3 Membri

7 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 19

Ultimi 30 Giorni: 88

Tutti i Tempi: 3,686