Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
L'immagine a sinistra (pannello frontale già rimosso) mostra la posizione dei ganci in metallo (in rosso) che fanno presa sulla cornice in plastica. Nei prossimi passi, cerca di fare leva sul pannello frontale dagli spazi tra i ganci.
-
-
-
Continua a fare leva sul bordo sinistro finché anche quelli superiore ed inferiore iniziano a separarsi dall'iPod Touch.
-
Dopo che i bordi superiore ed inferiore si sono sollevati leggermente dall'iPod Touch, usa lo strumento di apertura per assicurarti che la plastica che li circonda si sia staccata dai ganci all'interno dell'iPod.
-
-
-
Infila un piccolo strumento di apertura per iPod, con il bordo rivolto verso il retro dello schermo, tra la copertura in plastica bianca della retroilluminazione e la schermatura in metallo sottostante.
-
Fai leva lungo il bordo inferiore dello schermo per sollevarlo abbastanza da prenderlo con le dita, stando attento a non piegare lo schermo.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry the battery off the adhesive securing it to the metal display tray.
-
Remove the metal display tray and set it aside.
-
Lay the battery flat in the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single Phillips screw securing the gold pressure contact to the logic board.
-
Use a pair of tweezers to lift the Phillips screw out of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following three Phillips screws securing the logic board to the rear panel:
-
Two 2.3 mm screws
-
One 1.9 mm screw
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the edge of an iPod opening tool, flip up the control button ribbon cable retaining flap.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully remove the two large pieces of tape securing the ribbon cables to the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the edge of an iPod opening tool to peel back the protective rubber grommet to reveal a hidden Phillips screw.
-
Remove the hidden Phillips screw.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the remaining Phillips screw securing the upper logic board to the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully pull the lower logic board away from the lower edge of the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the edge of an iPod opening tool to carefully free the antenna connector cable from the adhesive securing it to the rear case.
-
Use the edge of your iPod opening tool to disconnect the antenna cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully peel the antenna cable off the adhesive securing it to the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the small strip of tape securing the antenna socket ribbon cable to the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the edge of an iPod opening tool to peel the antenna socket ribbon cable off the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the edge of an iPod opening tool to carefully peel the Wi-Fi ribbon cable off the adhesive securing it to the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use an iPod opening tool to pry the black plastic frame under the upper logic board up from the adhesive securing it to the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully remove the logic board assembly from the rear panel, minding any cables that may get caught.
-
Annulla: non ho completato questa guida.
Altre 23 persone hanno completato questa guida.
Un commento
is there a way to repair the headphone jack?
mine only gives out a tiny bit of the frequency response, no bass or treble at all, and i can tell it's probably the ribbon cable.