Introduzione

Replace a damaged rubber control button cover.

Accessing the internals of the 4th generation Shuffle is extremely difficult, as the rear panel is both glued to the front case and secured by metal retaining clips. It is highly unlikely that you will be able to remove the rear panel without inflicting cosmetic and/or structural damage.
  • Accessing the internals of the 4th generation Shuffle is extremely difficult, as the rear panel is both glued to the front case and secured by metal retaining clips. It is highly unlikely that you will be able to remove the rear panel without inflicting cosmetic and/or structural damage.

  • Before proceeding, be sure your Shuffle is switched off.

Aggiungi Commento

Use a combination of iPod opening tools and metal spudgers to pry the rear panel away from the Shuffle by the seam nearest the ON/OFF switch.
  • Use a combination of iPod opening tools and metal spudgers to pry the rear panel away from the Shuffle by the seam nearest the ON/OFF switch.

Aggiungi Commento

  • Remove the rear panel from the Shuffle.

Aggiungi Commento

  • If present, remove the thin black moisture seal covering the Shuffle's internals.

  • Remove the single 2.1 mm Phillips screw securing the logic board to the front case.

Aggiungi Commento

  • Use the edge of an iPod opening tool to flip up the retaining flap on the control button cable ZIF socket.

  • Be sure you are prying up on the hinged retaining flap, not the socket itself.

  • Use a pair of tweezers to gently pull the control button ribbon cable out of its socket.

Aggiungi Commento

  • Use an iPod opening tool to gently pry the battery off the adhesive securing it to the front case.

  • Lift the battery out of the front case, being sure not to strain its delicate leads.

Why not simplifying this delicate step by just cutting the wires and soldering the (also cutted) new battery’s wires onto them (without creating a short circuit of course!)

Frans Noordman - Replica

  • Insert the tip of a metal probe into the hole molded into the logic board retainer nearest the logic board.

  • Pry the retainer first away from the front of the front case, then pull it away from the side of the front case.

  • Remove the logic board retainer from the Shuffle.

Aggiungi Commento

  • Use the edge of an iPod opening tool to push the headphone jack down toward the center of the Shuffle.

Aggiungi Commento

  • Continue pushing the logic board down away from the top edge of the Shuffle.

  • Pull the logic board out of the front case by the side nearest the ON/OFF button and gently maneuver the headphone jack out of its recess in the front case.

  • Remove the logic board assembly from the Shuffle.

Aggiungi Commento

  • Remove the following four screws:

    • Two 1.2 mm Phillips screws with large heads.

    • Two 1.6 mm Phillips screws with small heads.

Aggiungi Commento

  • Use an iPod opening tool to pull the control button plate out of the front case.

  • Remove the control buttons from the Shuffle.

Aggiungi Commento

  • Push the rubber control button cover out of the front case.

  • When reinstalling the control button cover, be sure it is properly aligned and that its top and bottom edges are seated in the grooves cut into the front case.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Hola, quisiera saber donde poder localizar las piezas de repuesto de la botonera play/pause tanto la pieza electrónica como la botonera. Gracias

Verónica - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 11

Tutti i Tempi: 7,553