Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Riempi una pentola o una padella con abbastanza acqua per immergerci un iOpener.
-
Scalda l'acqua finché non bolle. Spegni il fuoco.
-
Posiziona l'iOpener nell'acqua calda per 2-3 minuti. Assicurati che l'iOpener sia completamente immerso nell'acqua.
-
Usa delle pinze per estrarre l'iOpener scaldato dall'acqua calda.
-
Asciuga accuratamente l'iOpener con un asciugamano.
-
Il tuo iOpener è pronto all'uso! Se devi scaldare di nuovo l'iOpener, scalda l'acqua fino all'ebollizione, spegni il fuoco e immergi l'iOpener in acqua per 2-3 minuti.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lay the iOpener over the plastic tab to loosen the adhesive. Let the bag sit on the device for approximately 90 seconds before attempting to open the panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a plastic opening tool to pull the rear plastic cover away from the device until there is enough room to insert a spudger.
-
Insert a spudger under the cover, then pry it up and away from the device.
-
Remove the rear plastic cover from the iPod.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 1.4 mm Phillips #000 screw from the black plastic spacer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a plastic opening tool to remove the black plastic spacer from the Nano.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 2 mm Phillips #000 screws from the bottom of the case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a plastic opening tool into the seam between the white plastic front panel and the rear case.
-
Slide the opening tool along the edge of the front panel to free it from clips and adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to press the midframe screw tab up and out of the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a metal spudger to carefully pry near the Lightning connector and under all parts of the front panel assembly: the front glass/digitizer, the LCD display and the metal midframe.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Continue prying along the edges under the front panel assembly, releasing the clips and adhesive along the sides of the device.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the front panel assembly slightly down and partially out of the device.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to release the digitizer cable and display data cable connectors.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently unfold the two halves of the device to access the internal components.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull up on the battery pull tab to free the battery from its adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Completely separate the front panel assembly from the rest of the device.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a spudger under the metal midframe and display on the left side of the home button.
-
Rotate the spudger around the home button and across the front panel, releasing the adhesive holding the display in place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Once all of the adhesive has been released, gently separate the display assembly from the front glass/digitizer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the six (three on each side) 1.5 mm Phillips #000 screws securing the metal midframe to the display.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If there is tape holding the midframe to the display, remove it with a plastic opening tool.
-
Annulla: non ho completato questa guida.
Altre 41 persone hanno completato questa guida.
2 Commenti
My display didn’t come out intact, so I ordered a new one but it has no metal backing. Where could I get it?
Love the guide. In performing this myself very useful, but there are may small details that would have helped me and for the first time novice such as:
- Describing in more detail how to separate the Digitizer and Display cables that intertwine and is connected to the home button.
- Recommend repair novice taking their own pictures as reference points to go back to
- Tools a good magnifying lens or a means to see small part details
- Provide more insight on how the display metal back is to be removed after folding back display cables and removing corner tape.
- Not all repair parts are the same; recommend basic instruction on common steps for parts that require re-applying the metal back, and folding over the cables
All-in-all a good guide…Thanks.