Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the large iPod opening tool into the seam between the front case and rear panel of the iPod, below the dock connector. Run the tool back and forth to create an opening. The tool's edge should point toward the rear panel to prevent any accidental scratching of the aluminum front case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a small iPod opening tool into the seam on the Hold button side of the iPod, with the edge of the tool pointing toward the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently enlarge the existing gap by pressing/wiggling the small iPod opening tool into the gap near each of the two tabs attached to the rear case, pushing the clips toward the center of the iPod until both have been freed.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Repeat the same procedure listed in the previous step to free the five clips along the headphone jack side of the iPod.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
After ensuring all tabs are free, separate the two halves of the iPod.
-
The rear panel is now free from the iPod.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 3 screws:
-
Two 3 mm Phillips screws near the dock connector.
-
One 4 mm Phillips screw along the edge of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel up the ground strap connecting the battery to the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the flat end of a spudger between the battery and the headphone jack side of the front case to pry the battery up off the adhesive securing it to the front case.
-
Rotate the battery out of the iPod and lay it next to the iPod. The battery is still soldered to the logic board by three wires, so don't remove it entirely.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently lift up on the dock connector end of the logic board to ensure the logic board is free.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the end of the logic board near the battery connector with one hand, and hold onto the rest of the iPod with your other hand.
-
Slide the logic board out of its holding brackets on the rear of the display.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to flip up the black plastic tab holding the orange display ribbon in place. The black tab will rotate up 90 degrees, releasing the ribbon cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to slide the display ribbon out of its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to flip up the black plastic tab holding the orange click wheel ribbon in place. The black tab will rotate up 90 degrees, releasing the ribbon cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to slide the click wheel ribbon out of its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
The logic board and battery are now free from the iPod.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to carefully pry up the adhesive holding down the edge of the display.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently lift up on one corner of the display to separate the adhesive holding the display in place.
-
Lift up on the other corner of the display in the same manner.
-
Annulla: non ho completato questa guida.
Altre 50 persone hanno completato questa guida.
2 Commenti
Noice! I accidentally stepped on my screen (TBF, my cat was in the way) so I decided to consult the almighty iFixit! I did have a bit of trouble removing the screen, though, as I found the adhesive too strong to pull. Therefore, I used my spudger as a lever to pull it out.
As this was my first intro into the world of DIY electronics repairing (that is to say, one that didn't have me losing every piece to it), I'm ready to see what else can come at me!
(Also, be careful not to put any fingerprints on the inside of the screen. I nearly did that, but some toilet paper and some isopropyl fixed it up.)