Salta al contenuto principale

iPhone XR Lower Speaker Replacement

Cosa ti serve

  1. iPhone XR Lower Speaker Replacement, Remove the pentalobe screws: passo 1, immagine 1 di 2 iPhone XR Lower Speaker Replacement, Remove the pentalobe screws: passo 1, immagine 2 di 2
    • Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

    • Power off your iPhone before beginning disassembly.

    • Remove the two 6.7 mm-long pentalobe screws at the bottom edge of the iPhone.

    • Opening the iPhone will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

    • There's a black rubber gasket just beneath the head on each pentalobe screw. For maximum protection against dust and liquid, check the condition of the gaskets or replace the screws during reassembly.

    One of my gaskets was as shown in your second photo, the other had been worked into the threads (as if smeared) probably from the factory and was completely unusable.

    In place of replacements (unsure of where to purchase) I just used a clear silicone caulking on both screws upon reassembly to offer at least some water seal. I wish these gaskets were included with the gasket waterproofing sealant kit!

    Erica - Replica

    Is there any place to buy these screw gaskets? I haven’t seen it mentioned anywhere but one of mine was pretty much chewed up. Silicone should work but I’d prefer the oem solution.

    Chilinh Nguyen - Replica

    I found a place on Amazon that sells them. It's cheapest to get a full set of screws than to get just these. $5-$6 USD.

    J Olin -

    Can it be dead?

    Lulu navarro - Replica

    If I transfer the data from the old to the new battery with an icopy, don't I get an error message?

    David Julian Krause - Replica

    how am i supposed to know if the battery is below 25% if the screen won't turn on?

    Beth Jackson - Replica

  2. iPhone XR Lower Speaker Replacement, Tape over any cracks: passo 2, immagine 1 di 3 iPhone XR Lower Speaker Replacement, Tape over any cracks: passo 2, immagine 2 di 3 iPhone XR Lower Speaker Replacement, Tape over any cracks: passo 2, immagine 3 di 3
    • If your iPhone has a cracked screen, keep further breakage contained and prevent bodily harm during your repair by taping over the glass.

    • Lay overlapping strips of clear packing tape over the iPhone's screen until the whole face is covered.

    • Wear safety glasses to protect your eyes from any glass shaken free during the repair.

    • If you can't get the suction cup to stick in the next few steps, fold a strong piece of tape (such as duct tape) into a handle and lift the screen with that instead.

    • If all else fails, you can superglue the suction cup to the screen.

    This looks like a repeat of Step 3.

    GenjideGaulle - Replica

  3. iPhone XR Lower Speaker Replacement, Anti-Clamp instructions: passo 3, immagine 1 di 3 iPhone XR Lower Speaker Replacement, Anti-Clamp instructions: passo 3, immagine 2 di 3 iPhone XR Lower Speaker Replacement, Anti-Clamp instructions: passo 3, immagine 3 di 3
    Attrezzo utilizzato in questo passaggio:
    Anti-Clamp
    $24.95
    Compra
    • The next three steps demonstrate the Anti-Clamp, a tool we designed to make the opening procedure easier. If you aren't using the Anti-Clamp, skip down three steps for an alternate method.

    • For complete instructions on how to use the Anti-Clamp, check out this guide.

    • Pull the blue handle backwards to unlock the Anti-Clamp's arms.

    • Slide the arms over either the left or right edge of your iPhone.

    • Position the suction cups near the bottom edge of the iPhone—one on the front, and one on the back.

    • Squeeze the cups together to apply suction to the desired area.

    • If you find that the surface of your iPhone is too slippery for the Anti-Clamp to hold onto, you can use tape to create a grippier surface.

  4. iPhone XR Lower Speaker Replacement: passo 4, immagine 1 di 3 iPhone XR Lower Speaker Replacement: passo 4, immagine 2 di 3 iPhone XR Lower Speaker Replacement: passo 4, immagine 3 di 3
    • Pull the blue handle forward to lock the arms.

    • Turn the handle clockwise 360 degrees or until the cups start to stretch.

    • Make sure the suction cups remain aligned with each other. If they begin to slip out of alignment, loosen the suction cups slightly and realign the arms.

  5. iPhone XR Lower Speaker Replacement: passo 5, immagine 1 di 3 iPhone XR Lower Speaker Replacement: passo 5, immagine 2 di 3 iPhone XR Lower Speaker Replacement: passo 5, immagine 3 di 3
    • Heat an iOpener and thread it through the arms of the Anti-Clamp.

    • You can also use a hair dryer, heat gun, or hot plate—but extreme heat can damage the display and/or internal battery, so proceed with care.

    • Fold the iOpener so it lays on the bottom edge of the iPhone.

    • Wait one minute to give the adhesive a chance to release and present an opening gap.

    • Insert an opening pick under the screen and the plastic bezel, not the screen itself.

    • If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle a quarter turn.

    • Don't crank more than a quarter turn at a time, and wait one minute between turns. Let the Anti-Clamp and time do the work for you.

    • Skip the next three steps.

    Please UPDATE THIS STEP to say 'insert the opening pick underneath the PLASTIC FRAME OF THE SCREEN' and not the screen. Way too many people are taking this as the way to do it then posting their screen looks different when it's open when they've actually removed the screen leaving the frame in place. It's not rocket science.

    [deleted] - Replica

    Thanks for the suggestion! We updated this step to clarify that.

    Arthur Shi -

  6. iPhone XR Lower Speaker Replacement, Heat up the screen: passo 6, immagine 1 di 1
    • Heating the lower edge of the iPhone helps soften the adhesive securing the display, making it easier to open.

    • Use a hairdryer or heat gun, or prepare an iOpener and apply it to the lower edge of the iPhone for about a minute in order to soften up the adhesive underneath.

    An alternative to the Iopener or heat gun is to heat water to EXACTLY 80 degrees F (cooking thermometer is great for this) and pour into a reinforced ziplock type bag. Leave the bag on the screen, but be sure that none of the hot water rests on the zipper portion, as the water is hot enough to soften that seal and leak out on to your device! This meat had is my personal favorite as the heat is distributed very equally and precisely as compared to a heat gun, but is more accessible than the Iopener.

    Colin Wylie - Replica

    When using an iOpener, rest the glossy (transparent) side on the phone so it contacts the phone and conducts heat easily

    Afiq - Replica

  7. iPhone XR Lower Speaker Replacement: passo 7, immagine 1 di 2 iPhone XR Lower Speaker Replacement: passo 7, immagine 2 di 2
    • If you're using a single suction handle, apply it to the bottom edge of the phone, while avoiding the curved portion of the glass.

  8. iPhone XR Lower Speaker Replacement, Lift the display slightly: passo 8, immagine 1 di 3 iPhone XR Lower Speaker Replacement, Lift the display slightly: passo 8, immagine 2 di 3 iPhone XR Lower Speaker Replacement, Lift the display slightly: passo 8, immagine 3 di 3
    • Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.

    • Insert an opening pick under the screen and the plastic bezel, not the screen itself.

    • The watertight adhesive holding the display in place is very strong; creating this initial gap takes a significant amount of force. If you're having a hard time opening a gap, apply more heat, and gently rock the screen up and down to weaken the adhesive until you create enough of a gap to insert your tool.

  9. iPhone XR Lower Speaker Replacement, Separate the screen adhesive: passo 9, immagine 1 di 3 iPhone XR Lower Speaker Replacement, Separate the screen adhesive: passo 9, immagine 2 di 3 iPhone XR Lower Speaker Replacement, Separate the screen adhesive: passo 9, immagine 3 di 3
    • Slide the opening pick around the lower left corner and up the left edge of the iPhone, slicing through the adhesive holding the display in place.

    • Don't insert your pick more than 3 mm, as you may damage internal components.

    I think it's important to note that depending on how a screen was damaged, make sure to insert the pic under the black bezel directly under the actual screen. This bezel is a frame around the digitizer. I unknowingly inserted the pic between the bezel and the screen, and separated them both. I did this all the way around the phone. So I basically had to struggle to keep together two different sections of the display assembly because of this mishap, until I removed all the ribbon connectors. It made things much more difficult.

    Dave - Replica

    An edit to my above comment: by digitzer, I mean the LCD shield. My apologies.

    Dave - Replica

  10. iPhone XR Lower Speaker Replacement, Screen information: passo 10, immagine 1 di 1
    • There are delicate cables along the right edge of your iPhone. Don't insert your pick at the marked spots, as you may damage the cables.

  11. iPhone XR Lower Speaker Replacement: passo 11, immagine 1 di 3 iPhone XR Lower Speaker Replacement: passo 11, immagine 2 di 3 iPhone XR Lower Speaker Replacement: passo 11, immagine 3 di 3
    • Re-insert your pick at the bottom edge of the iPhone, and slide it up the right side to continue separating the adhesive.

    • Don't insert your pick more than 3 mm, as you may damage the display cables.

    My replacement screen for the XR has a black rim but it looks pink. Is that normal?

    Irwin Cantor - Replica

    You can use some Isopropyl alcohol in a syringe with a thin needle to soften even more the adhesive around the screen. But be careful so as not to overdo it. Just a few drops. It will become more easier to remove the screen.

    Dan Brock - Replica

    Step 11 says not to insert your pick around the right side to avoid damaging cables, then Step 12 says to insert it on the right side. Help, I'm confused!

    ingwis - Replica

    Hi there!

    Thank you for the feedback! The wording in step 11 was definitely ambiguous, so we have changed it! You only need to avoid the marked spots rather than the right edge.

    Alex Diaz-Kokaisl -

  12. iPhone XR Lower Speaker Replacement: passo 12, immagine 1 di 3 iPhone XR Lower Speaker Replacement: passo 12, immagine 2 di 3 iPhone XR Lower Speaker Replacement: passo 12, immagine 3 di 3
    • The top edge of the display is secured with both glue and clips.

    • Slide the opening pick around the top corner of the display, while gently pulling or wiggling the display down in the direction of the Lightning port.

    • The clips will break if you use too much force. Work carefully and be patient.

    • Don't insert your pick more than 3 mm, as you may damage the front panel sensor array.

    • Slide the pick to the opposite corner and cut any remaining adhesive securing the display.

  13. iPhone XR Lower Speaker Replacement: passo 13, immagine 1 di 1
    • Pull on the small nub on the suction cup to remove it from the front panel.

  14. iPhone XR Lower Speaker Replacement, Open the iPhone: passo 14, immagine 1 di 3 iPhone XR Lower Speaker Replacement, Open the iPhone: passo 14, immagine 2 di 3 iPhone XR Lower Speaker Replacement, Open the iPhone: passo 14, immagine 3 di 3
    • Open the iPhone by swinging the display up from the left side, like the back cover of a book.

    • Don't try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone's logic board.

    • Lean the display against something to keep it propped up while you're working on the phone.

    • During reassembly, lay the display in position, align the clips along the top edge, and carefully press the top edge into place before snapping the rest of the display down. If it doesn't click easily into place, check the condition of the clips around the perimeter of the display and make sure they aren't bent.

    sure looks like the "hinge" is on the right hand side to me.. not left...!

    Doug Trout - Replica

    If you leave the suction cup attached to the screen during the “hinging” process, it makes for a very handy holder for the screen until it’s completely detached.

    Richard Deubler - Replica

    What about the sticky black adhesive clinging to the inside of the case?

    Ronald - Replica

  15. iPhone XR Lower Speaker Replacement, Unscrew the battery connector cover: passo 15, immagine 1 di 2 iPhone XR Lower Speaker Replacement, Unscrew the battery connector cover: passo 15, immagine 2 di 2
    Attrezzo utilizzato in questo passaggio:
    Magnetic Project Mat
    $19.95
    Compra
    • Remove three 1.2 mm Y000 screws securing the battery connector cover bracket.

    • Remove the bracket.

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.

    • During reassembly, this is a good point to power on your iPhone and test all functions before you seal the display in place. Be sure to power your iPhone back down completely before you continue working.

    Definitely make sure all three lobes of your tool are aligned before use (it’s a little harder to tell with this style of bit) and apply even and adequate pressure to ensure it grabs as you spin the driver to prevent disfiguring the lobes/slot of the screw head.

    Unfortunately my Y000 tool was perhaps not the best fit (tolerance a bit off) in these screws and I ended up stripping out the heads of all three of these. I started to panic but after I sanded the tip of my Y000 bit down a little with super fine grit (1000CW-C) sand paper to flatten the domed tip (visible with macro lens) and give it a bit more bite I was able to remove and reinstall without issue—in fact I had to remove and install them twice since I forgot my adhesive tape during reassembly, so the screws survived and the sanded bit worked.

    Erica - Replica

    +1 to above comment. I bought a cheap kit from Amazon and the Y000 screw driver is not good for this job. I’m concerned that I may have disfigured the heads and i type this comment in the midst of my fix :D Be gentle and assess if you can remove at least one screw with your driver before rummaging through all three and other similar screws holding display connector as well.

    Shan Potti - Replica

    Update to above comment. I got hold of a Y0.8 screw driver bit (lucky to find an ORIA screw driver kit in my office) and it works like wonders :) Now back to work…

    Shan Potti - Replica

  16. iPhone XR Lower Speaker Replacement, Disconnect the battery: passo 16, immagine 1 di 2 iPhone XR Lower Speaker Replacement, Disconnect the battery: passo 16, immagine 2 di 2
    • Use the point of a spudger to pry the battery connector straight up out of its socket.

    • Try not to damage the black silicone seal surrounding this and other board connections. These seals provide extra protection against water and dust intrusion.

    • Bend the connector slightly away from the logic board to prevent it from accidentally making contact with the socket and providing power to the phone during your repair.

  17. iPhone XR Lower Speaker Replacement, Unscrew the display connector cover: passo 17, immagine 1 di 2 iPhone XR Lower Speaker Replacement, Unscrew the display connector cover: passo 17, immagine 2 di 2
    • Remove the two 1.2 mm Y000 screws securing the display connector bracket.

    • Remove the bracket.

    What if the screw is damaged and you can’t get one out?

    Kashawn Benjamin - Replica

  18. iPhone XR Lower Speaker Replacement, Disconnect the digitizer: passo 18, immagine 1 di 2 iPhone XR Lower Speaker Replacement, Disconnect the digitizer: passo 18, immagine 2 di 2
    • Use the tip of a spudger to pry up and disconnect the digitizer cable.

    • To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

    • If any part of your screen doesn't respond to touch after your repair, disconnect the battery and then re-seat this connector, making sure it clicks fully into place and that there's no dust or other obstruction in the socket.

  19. iPhone XR Lower Speaker Replacement, Disconnect the display: passo 19, immagine 1 di 2 iPhone XR Lower Speaker Replacement, Disconnect the display: passo 19, immagine 2 di 2
    • Use the tip of a spudger to disconnect the display cable connector.

    The new display cable isn’t snapping in but I was just able to snap in the old one. Did I break the new one somehow?

    Andrew Pierson - Replica

    Same it is really frustrating, just keeps slipping up and its bound to get damaged

    Daniel Maldonado - Replica

  20. iPhone XR Lower Speaker Replacement, Unscrew the logic board connector cover: passo 20, immagine 1 di 2 iPhone XR Lower Speaker Replacement, Unscrew the logic board connector cover: passo 20, immagine 2 di 2
    • Remove the five screws securing the logic board connector bracket to the rear case:

    • One 1.3 mm Phillips #000 screw

    • One 1.5 mm Phillips #000 screw

    • Three 1.2 mm Y000 screws

    • Remove the bracket.

    • Be careful not to lose the smaller bracket clipped onto the edge. It's secured with a small clip and is easy to accidentally knock off of the larger bracket.

    Phillips screw 1.3 mm on last step is not working. The small clipped bracket has been damaged. This screw perhaps should be the first, before 1.2 Y000. - To be confirmed by others.

    Dmitri - Replica

    I’m not sure it makes much if any difference, but we went ahead and swapped the order for you guys. Thanks for your comments!

    Jeff Suovanen - Replica

    I just repaired another XR, and you are right! It doesn’t make any differnerce in the order these screws come out. I still damaged this fragile piece. As I work on more of these, I’ll figure out a way to remove this screw without damaging the clip. For now everyone, just use extra caution when removing the 1.3mm phillips screw! Thanks Jeff

    fabianowens -

    I’ve now done at least 6 of these so far and I have fairly consistent good results by taking the 2 Philips head screws out first, then doing the Y screws.

    Stow -

    Is this piece important for the repair if broken? I have broken it on a home repair. What is it used for? Is it a grounding connection or is it completely unimportant. More information needed please

    Squishy Horses - Replica

    I’m wondering that too. Is this piece important?

    Phillip Gross -

    My clip broke too! on iphone XR. Any word on necessity?

    Beth Buer - Replica

    I can confirm that taking out the 1.3 mm screw first then the 1.5 mm screw works the best. If done correctly, you should be able to to remove the rest of the screws and pull the panel off with the clip still attached to the panel. For reassembly, start with the 1.5 mm screw then the 1.3 mm screw.

    Carlos Oulman - Replica

    I don’t remove the small screw at all. I just slide out the metal cover plate and slide back in to reassemble.

    Kyaw-Zin Win - Replica

    this is what i have done as well. Care is still needed to avoid damaging this part. However, it is seemingly far less prone to damage or loss and thus less risky for this repair process.

    Justin Parsons -

    I too broke this shield. In looking over this problem I believe it’s best to loosen, but not remove, either screw first then the other. To be clear, loosen the red or yellow screw but only just to break it free, then the second screw. Then remove both and the others and the shield should remain in one piece. I put it back with the broken part (on the red screw) and made sure the two are in contact so there’s conductivity as these shields serve a purpose other than just holding in connectors. My phone works fine with this fix.

    pgrobin - Replica

    Is this small bracket important if broken??

    Phillip Gross - Replica

    Mine is broken

    Easy Repair - Replica

    Mine is broken and my apple pay doesn’t work. Something to do with NFC antenna this little clip??

    Marcos Fernández - Replica

    I'm guessing so. I replaced a screen on a phone I bought from a friend. I noticed this bracket was broken when I disassembled the phone but didn't think much of it. When I reassembled it my NFC also does not work. Bummer. A lot of people in these comments have asked if it is crucial that this bracket be connected. Can someone from iFixit or other please reply to those comments?

    Larry Jorgenson -

    On the 1.3 mm screw I actually chose not to remove it. I broke it loose then used the tip of the spudger to simply twist the bracket out of the way, with the screw still attached. Then I could remove the larger bracket.

    mpalma - Replica

    Kyaw-Zin is right because the shield contains of two tin parts. But there is another option:

    1. Unscrew the yellow and orange screws first.

    2. Lift the shield gently that it can turn about 20° anticlockwise.

    3. Open the red screw and let the shield turn with it the first degrees.

    Daniel Brehm - Replica

    The first time I did this repair, I didn’t see the comments ahead of time and broke the bracket, even removing the 1.3mm screws first. The second time I did the repair, I was prepared and being extra careful, but the simple act of turning the 1.3mm screw head was enough to break it. If I ever have to do this repair again, I’ll just leave the screw in and try to slide the plate out with the screw (and bracket, hopefully) still in tact, as per Kyaw-Zin Win.

    Debbie Thompson - Replica

    None of the screw driver bits I got fits the 1.3mm and 1.5mm screws. How do I remove them?

    Jonatious Joseph Jawahar - Replica

    Same issue as above. The bits provided in the kit do not work with the 1.3mm and 1.5mm screws

    Graham Hammell - Replica

    Further to above comment about bit not working. Had to go and purchase another PH000 from Home Depot and that worked

    Graham Hammell - Replica

    I’ve broken that little bracket attached to the red screw. Is it important and can I get a replacement????? Thanks all

    steve.arfa - Replica

    Broken the clip. Is this important??

    kyledrumtutor - Replica

    Yikes, broke mine too. Oh god. Think perhaps the delicate 1.3mm should come out first when everything else is secure...

    Ronald - Replica

    Don't remove the 1.3 Phillips screw! Twisting this screw will break the smaller bracket that is clipped to the larger. Remove all the other screws. Block the smaller bracket from moving as you gently slide the larger bracket horizontally toward the battery until free. The smaller bracket can stay in place while the screen is replaced. When reassembling, support the small bracket by backing with a spudger or similar tool.

    doug68242 - Replica

    I just broke the smaller bracket also :( I didn´t notice these comments until now :(

    It looks like part of the antenna for NFC, as all except NFC works on my iPhone now.

    It should be repairable using some wire wrap wire, either twisted around the two screws that connected that part of the bracket (or soldered in place). I will try and report back if it works.

    Richard Croyle - Replica

    Success!! I managed to re-construct the small arm of the bracket by screwing the 1.3mm screw back in with some 0.3mm enamel wire soldered into what was left of the small bracket arm on the screw, then the other end of the enamel wire I wrapped under the 1.5 wire screw's head (enamel exposed to bare metal), then screwed both screws down. also I lifted up the small metal arm with a screw driver (to make sure it reconnects with the display grounding square) ..and NFC worked again (slightly different antenna pattern mind (need to place cards slightly higher up the rear of the phone). Anyway works again :)

    Richard Croyle - Replica

  21. iPhone XR Lower Speaker Replacement, Disconnect the front sensors: passo 21, immagine 1 di 2 iPhone XR Lower Speaker Replacement, Disconnect the front sensors: passo 21, immagine 2 di 2
    • Use the tip of a spudger to pry the front sensor assembly connector up from its socket.

    During testing, make sure your proximity sensor is not on upside down, as it’s easy to connect upside down. Your phone will boot loop if it’s on incorrectly.

    Tristan England - Replica

  22. iPhone XR Lower Speaker Replacement, Remove the display assembly: passo 22, immagine 1 di 1

    unclear if this is where screen removal ends

    Daniel Maldonado - Replica

    I had the same question, but the answer is yes. Steps 21-30 are removing parts from the original screen that need to be reattached onto the new screen. You are no longer working inside the frame, but on the back of the screen itself.

    amclean78 - Replica

    I apologize for missing these comments initially, but yes that’s correct, the screen is removed now and the rest of the guide goes on to other parts, either in the phone or on the back of the screen. Good luck with the repair!

    Adam O'Camb -

    The alternate method of removing the battery should be highlighted as a standard option. There is so much more work and potential to damage the parts than if you left them in place and carefully with plenty of heat remove the battery. I so wish I had seen this before!

    Martin Kappeyne - Replica

  23. iPhone XR Lower Speaker Replacement, Lower Speaker: passo 23, immagine 1 di 1
    • Remove the seven screws securing the bracket below the Taptic engine and speaker:

    • Three Phillips 1.4 mm screws

    • Two Phillips 1.7 mm screws

    • One Phillips 1.9 mm screw

    • One Phillips 1.6 mm screw

    Why remove all this stuff for the battery? Is it necessary to do any of steps from here to 32 for the battery at all?

    Paul Butterworth - Replica

    Removing these parts facilitates removing the bottom adhesive tabs but is not necessary. If you remove the upper adhesive tabs, then heat the backside of the lower ones (which you do if you couldn't get the tabs out), the battery comes out easily. Removes 14 steps from this procedure.

    teamhudson - Replica

  24. iPhone XR Lower Speaker Replacement: passo 24, immagine 1 di 2 iPhone XR Lower Speaker Replacement: passo 24, immagine 2 di 2
    • Lift the bracket from the edge nearest the battery. Don't try to fully remove it, as it's still connected via a small flex cable.

  25. iPhone XR Lower Speaker Replacement: passo 25, immagine 1 di 2 iPhone XR Lower Speaker Replacement: passo 25, immagine 2 di 2
    • While holding the bracket out of the way, use the point of a spudger to pry up and disconnect the flex cable underneath.

  26. iPhone XR Lower Speaker Replacement: passo 26, immagine 1 di 1
    • Remove the bracket.

  27. iPhone XR Lower Speaker Replacement: passo 27, immagine 1 di 2 iPhone XR Lower Speaker Replacement: passo 27, immagine 2 di 2
    • Remove the piece of black tape and the small rubber rectangle covering the Taptic Engine connector cover.

  28. iPhone XR Lower Speaker Replacement: passo 28, immagine 1 di 1
    Attrezzo utilizzato in questo passaggio:
    Standoff Screwdriver for iPhones
    $5.49
    Compra
    • Remove the five screws securing the lower speaker:

    • One 2.8 mm standoff screw

    • Standoff screws are best removed using a dedicated standoff driver or driver bit.

    • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

    • One 2.3 mm standoff screw

    • One 2.3 mm Phillips screw

    • One 1.8 mm Phillips screw

    • One 1.6 mm Phillips screw

    I was able to get the 2.8mm standoff screw out with a 1.5 mm flat head from my iFixit kit but was not able to find anything to get the 2.3mm screw out. Buying the standoff screwdriver begrudgingly. I wish I'd known about this before I started.

    leeprobert - Replica

    I was able to get the 2.3mm stand-off screw out by using my 1.5mm flat head to push along the outside of this screw. Took a bit to fully back it out but it worked just fine.

    Stretch - Replica

    Recommend PH00 for the 1.8 and PH000 for the rest.

    Sam Omiotek - Replica

  29. iPhone XR Lower Speaker Replacement: passo 29, immagine 1 di 2 iPhone XR Lower Speaker Replacement: passo 29, immagine 2 di 2
    • Remove the small bracket on the top right corner of the speaker.

    • Remove the Taptic Engine connector cover.

    When reassembling the speaker bracket, stick the flat end of a spudger on the right side while screwing it down so it doesn’t fall out the side and to maintain its alignment.

    Afiq - Replica

  30. iPhone XR Lower Speaker Replacement: passo 30, immagine 1 di 2 iPhone XR Lower Speaker Replacement: passo 30, immagine 2 di 2
    • Insert a spudger under the top edge of the speaker near the edge of the iPhone's case.

    • Gently pry up and lift the top edge of the speaker.

  31. iPhone XR Lower Speaker Replacement: passo 31, immagine 1 di 3 iPhone XR Lower Speaker Replacement: passo 31, immagine 2 di 3 iPhone XR Lower Speaker Replacement: passo 31, immagine 3 di 3
    • Hold the speaker by its side edges and rock it side-to-side, separating the adhesive securing it to the bottom edge of the iPhone.

    • Pull the speaker away from the bottom edge of the iPhone until the adhesive gasket separates.

  32. iPhone XR Lower Speaker Replacement: passo 32, immagine 1 di 2 iPhone XR Lower Speaker Replacement: passo 32, immagine 2 di 2
    • Remove the speaker.

    • The speaker's adhesive gasket is not reusable. Peel away any remaining adhesive residue with tweezers.

    • To help protect against water and dust intrusion, replace the adhesive gasket during reassembly. Prep the area by cleaning it with a bit of isopropyl alcohol and a lint-free cloth or coffee filter so that the gasket adheres properly. Install a new gasket onto the speaker, and then install the speaker.

    you may be able to reuse the gasket if you heat the glue. You may want to consider this because I can’t find the gasket through ifixit.

    HAYDEN MYERS - Replica

    ? I agree !

    JoeBlog - Replica

    do we have to remove all the extra stuff such as this if we're just replacing screen display? what is the importance?

    destiny velasco - Replica

    If you want to get the surface prepped nicely, tightly roll up the corner of a KimTech wipe, add some IP, then gently use your spudger tip to wipe excess gasket material from the area. Take your time!

    Tal Pipkin - Replica

Conclusione

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Altre 19 persone hanno completato questa guida.

Adam O'Camb

Membro da: 04/11/15

195.355 Reputazione

416 Guide realizzate

Un commento

Where can I buy a replacement gasket for the speaker?

Darrian Aguirre - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 21

Ultimi 7 Giorni: 158

Ultimi 30 Giorni: 633

Tutti i Tempi: 57,322