Salta al contenuto principale

iPhone 7 Volume Control Buttons Replacement

Cosa ti serve

  1. iPhone 7 Volume Control Buttons Replacement, Pentalobe Screws: passo 1, immagine 1 di 1
    • Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

    • Power off your iPhone before beginning disassembly.

    • Remove the two 3.4 mm pentalobe screws on the bottom edge of the iPhone.

    • Opening the iPhone's display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

  2. iPhone 7 Volume Control Buttons Replacement, iPhone 7 Opening Procedure: passo 2, immagine 1 di 1
    • Heating the lower edge of the iPhone will help soften the adhesive securing the display, making it easier to open.

    • Use a hairdryer or prepare an iOpener and apply it to the lower edge of the iPhone for about a minute in order to soften up the adhesive underneath.

  3. iPhone 7 Volume Control Buttons Replacement: passo 3, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 3, immagine 2 di 2
    • Attach a suction cup to the lower half of the display assembly, just above the home button.

    • Be sure the suction cup does not overlap with the home button, as this will prevent a seal from forming between the suction cup and front glass.

    • If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.

  4. iPhone 7 Volume Control Buttons Replacement: passo 4, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 4, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 4, immagine 3 di 3
    • Pull up on the suction cup to create a small gap between the display assembly and the rear case.

    • Insert the flat end of a spudger into the gap.

    • The watertight adhesive holding the display in place is very strong, and creating this initial gap takes a significant amount of force. If you're having a hard time opening a gap, rock the screen up and down to weaken the adhesive until you can fit a spudger inside.

  5. iPhone 7 Volume Control Buttons Replacement: passo 5, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 5, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 5, immagine 3 di 3
    • Slide the spudger to the left along the lower edge of the iPhone.

    • Twist the spudger to widen the gap between the display and rear case.

  6. iPhone 7 Volume Control Buttons Replacement: passo 6, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 6, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 6, immagine 3 di 3
    • Slide the spudger up the left side of the iPhone, starting at the lower edge and moving towards the volume control buttons and silent switch.

    • Do not pry along the top edge of the phone, you risk damaging the plastic clips securing the display.

  7. iPhone 7 Volume Control Buttons Replacement: passo 7, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 7, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 7, immagine 3 di 3
    • Insert the flat edge of a spudger into the bottom right corner of the device.

    • Twist the spudger to widen the gap between the display assembly and the rear case.

    • Slide the flat end of the spudger up the right side of the phone to break up the adhesive holding the display in place.

    • Do not insert the spudger further than the adhesive to avoid damaging delicate ribbon cables along the right edge.

  8. iPhone 7 Volume Control Buttons Replacement: passo 8, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 8, immagine 2 di 2
    • Pull up on the suction cup to lift up the display and open the iPhone.

    • Do not raise the display more than 10º as there are ribbon cables along the right edge of the device connecting the display to the logic board.

  9. iPhone 7 Volume Control Buttons Replacement: passo 9, immagine 1 di 1
    • Pull up on the small nub on the suction cup to remove it from the front panel.

  10. iPhone 7 Volume Control Buttons Replacement: passo 10, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 10, immagine 2 di 2
    • Slide an opening pick along the top edge of the iPhone, between the rear case and front panel, to break up the remaining adhesive holding the screen in place.

    • Be careful not to damage the plastic clips on the top edge of the phone.

  11. iPhone 7 Volume Control Buttons Replacement: passo 11, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 11, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 11, immagine 3 di 3
    • Pull the display assembly slightly away from the top edge of the phone to disengage the clips holding it to the rear case.

    • Open the iPhone by swinging the display up from the left side, like the back cover of a book.

    • Don't try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone's logic board.

  12. iPhone 7 Volume Control Buttons Replacement, Battery Disconnection: passo 12, immagine 1 di 1
    Attrezzo utilizzato in questo passaggio:
    Tri-point Y000 Screwdriver
    $5.99
    Compra
  13. iPhone 7 Volume Control Buttons Replacement: passo 13, immagine 1 di 1
    • Remove the lower connector bracket.

  14. iPhone 7 Volume Control Buttons Replacement: passo 14, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 14, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 14, immagine 3 di 3
    • Use the point of a spudger to lift the battery connector out of its socket on the logic board.

    • Bend the connector cable up slightly to prevent it from making contact with the socket and providing power to the phone.

  15. iPhone 7 Volume Control Buttons Replacement, Display Assembly: passo 15, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement, Display Assembly: passo 15, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement, Display Assembly: passo 15, immagine 3 di 3
    • Make sure the battery is disconnected before you disconnect or reconnect the cables in this step.

    • Use a spudger or a fingernail to disconnect the two lower display connectors by prying them straight up from their sockets on the logic board.

    • To reconnect these cables, press down on one end until it clicks into place, then repeat on the opposite end. Do not press down on the middle. If the connector is even slightly misaligned, the connector can bend, causing permanent damage.

    • If you have a blank screen, white lines on the display, or partial or complete lack of touch response after reassembling your phone, try disconnecting and carefully reconnecting both of these cables and make sure they are fully seated.

  16. iPhone 7 Volume Control Buttons Replacement: passo 16, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 16, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 16, immagine 3 di 3
    • Remove the two 1.3 mm Phillips #000 screws securing the bracket over the front panel sensor assembly connector.

    • Some phones could be Y000. Apple started using Y000 for these at some point in the middle of the product's lifecycle.

  17. iPhone 7 Volume Control Buttons Replacement: passo 17, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 17, immagine 2 di 2
    • Disconnect the front panel sensor assembly connector from its socket on the logic board.

    • This press connector should also be reconnected one end at a time to minimize the risk of bending.

  18. iPhone 7 Volume Control Buttons Replacement: passo 18, immagine 1 di 1
  19. iPhone 7 Volume Control Buttons Replacement, SIM Card: passo 19, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement, SIM Card: passo 19, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement, SIM Card: passo 19, immagine 3 di 3
    • Insert a SIM card eject tool or a paperclip into the small hole in the SIM card tray.

    • Press to eject the tray.

    • This may require a significant amount of force. However, ensure the eject tool is properly aligned beforehand as to not damage the eject mechanism inside the phone.

    • Remove the SIM card tray assembly from the iPhone.

    • When reinserting the SIM card, ensure that it is in the proper orientation relative to the tray.

  20. iPhone 7 Volume Control Buttons Replacement, Logic Board Connectors: passo 20, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement, Logic Board Connectors: passo 20, immagine 2 di 2
    • Use the flat end of a spudger to disconnect the rear-facing camera connector.

  21. iPhone 7 Volume Control Buttons Replacement: passo 21, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 21, immagine 2 di 2
    • Remove the following Phillips screws securing the rear camera bracket to the rear case:

    • One 1.3 mm screw

    • One 2.5 mm screw

  22. iPhone 7 Volume Control Buttons Replacement: passo 22, immagine 1 di 1
    • Remove the bracket.

  23. iPhone 7 Volume Control Buttons Replacement: passo 23, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 23, immagine 2 di 2
    • Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module.

  24. iPhone 7 Volume Control Buttons Replacement: passo 24, immagine 1 di 1
    • Remove the two 1.2 mm tri-point screws securing the upper cable bracket.

  25. iPhone 7 Volume Control Buttons Replacement: passo 25, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 25, immagine 2 di 2
    • Remove the upper cable bracket.

  26. iPhone 7 Volume Control Buttons Replacement: passo 26, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 26, immagine 2 di 2
    • Use the flat end of a spudger to disconnect the upper cable connector.

  27. iPhone 7 Volume Control Buttons Replacement: passo 27, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 27, immagine 2 di 2
    • Remove the four Phillips screws securing the Wi-Fi antenna:

    • Three 1.2 mm screws

    • One 1.7 mm screw

  28. iPhone 7 Volume Control Buttons Replacement: passo 28, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 28, immagine 2 di 2
    • Remove the top left antenna.

  29. iPhone 7 Volume Control Buttons Replacement: passo 29, immagine 1 di 1
    • Remove the following Phillips screws:

    • One 1.3 mm screw

    • One 2.2 mm screw

  30. iPhone 7 Volume Control Buttons Replacement: passo 30, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 30, immagine 2 di 2
    • Remove the bracket.

  31. iPhone 7 Volume Control Buttons Replacement: passo 31, immagine 1 di 1
    Attrezzo utilizzato in questo passaggio:
    Standoff Screwdriver for iPhones
    $5.49
    Compra
    • Remove the 2.2 mm standoff screw from the grounding bracket.

    • Standoff screws are best removed using a standoff screwdriver or bit.

    • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

  32. iPhone 7 Volume Control Buttons Replacement: passo 32, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 32, immagine 2 di 2
    • Use tweezers to gently bend the logic board grounding bracket out of the way.

  33. iPhone 7 Volume Control Buttons Replacement, Logic Board: passo 33, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement, Logic Board: passo 33, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement, Logic Board: passo 33, immagine 3 di 3
    • Use the point of a spudger to lift the two antenna cable connectors up off of the sockets on the logic board.

  34. iPhone 7 Volume Control Buttons Replacement: passo 34, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 34, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 34, immagine 3 di 3
    • Use tweezers to gently derout the antenna cables from the metal bracket on the logic board.

  35. iPhone 7 Volume Control Buttons Replacement: passo 35, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 35, immagine 2 di 2
    • Use the point of a spudger to disconnect the lower cable connector.

  36. iPhone 7 Volume Control Buttons Replacement: passo 36, immagine 1 di 1
    Attrezzo utilizzato in questo passaggio:
    Standoff Screwdriver for iPhones
    $5.49
    Compra
    • Remove the following screws:

    • One 1.4 mm Phillips screw

    • Three 2.2 mm standoff screws

    • Standoff screws are best removed using a standoff driver.

    • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

  37. iPhone 7 Volume Control Buttons Replacement: passo 37, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 37, immagine 2 di 2
    • Use the point of a spudger to move the SIM card eject plunger out of the logic board's way.

  38. iPhone 7 Volume Control Buttons Replacement: passo 38, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 38, immagine 2 di 2
    • Use the flat end of a spudger to gently lift the battery connector end of the logic board up.

    • Make sure you're not pulling against any cables. If you feel resistance, check all cables, connectors, and components are clear of the board.

  39. iPhone 7 Volume Control Buttons Replacement: passo 39, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 39, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 39, immagine 3 di 3
    • Lift the battery connector end of the logic board and pull it up and out of the rear case.

    • Be careful not to snag the logic board on any cables.

  40. iPhone 7 Volume Control Buttons Replacement, Rear Case Battery: passo 40, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement, Rear Case Battery: passo 40, immagine 2 di 2
    • Use a pair of tweezers with blunt tips to peel back one of the adhesive strips on the lower edge of the battery.

  41. iPhone 7 Volume Control Buttons Replacement: passo 41, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 41, immagine 2 di 2
    • Use a pair of tweezers with blunt tips to peel back the other adhesive strip on the lower edge of the battery.

  42. iPhone 7 Volume Control Buttons Replacement: passo 42, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 42, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 42, immagine 3 di 3
    • Try to keep the strips flat and unwrinkled during this procedure; wrinkled strips will stick together and break instead of pulling out cleanly.

    • Slowly pull one battery adhesive tab away from the battery, toward the bottom of the iPhone.

    • Pull steadily, maintaining constant tension on the strip until it slips out from between the battery and the rear case. For best results, pull the strip at a 60º angle or less.

    • The strip will stretch to many times its original length. Continue pulling and re-grab the strip near the battery if necessary.

  43. iPhone 7 Volume Control Buttons Replacement: passo 43, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 43, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 43, immagine 3 di 3
    • Repeat the previous step for the second strip.

    • Hold down the battery as you remove the second strip, or the strip may fling the battery when it separates from the case.

    • If you removed both adhesive strips successfully, skip the next step.

    • Otherwise, if either of the adhesive strips broke off underneath the battery and could not be retrieved, continue with the next step below.

  44. iPhone 7 Volume Control Buttons Replacement: passo 44, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 44, immagine 2 di 2
    Attrezzo utilizzato in questo passaggio:
    Plastic Cards
    $2.99
    Compra
    • If you successfully removed both adhesive strips, move on to the next step. Otherwise, you will need to pry the battery from the rear case.

    • Prepare an iOpener and apply it to the back of the rear case, directly over the battery. Alternatively, you can apply heat using a heat gun or hair dryer.

    • After about a minute, remove the iOpener, flip the phone over and use a plastic card to break up any remaining adhesive behind the battery.

    • Avoid bending the battery. Damage to the battery may release dangerous chemicals, and could start a fire.

    • Do not pry under the top third of the battery, you may damage the volume button ribbon cable.

  45. iPhone 7 Volume Control Buttons Replacement: passo 45, immagine 1 di 1
    • Remove the battery from the rear case.

    • When installing the battery, refer to this guide to replace your battery's adhesive strips.

  46. iPhone 7 Volume Control Buttons Replacement, Power and Volume Control Cable: passo 46, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement, Power and Volume Control Cable: passo 46, immagine 2 di 2
    • Remove the following Phillips screws:

    • Two 1.9 mm screws securing the power button.

    • Three 2.3 mm screws securing the volume buttons.

  47. iPhone 7 Volume Control Buttons Replacement: passo 47, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 47, immagine 2 di 2
    • Remove the following 1.3 mm Phillips screws:

    • One screw beside the rear-facing camera

    • One screw on the rear case

  48. iPhone 7 Volume Control Buttons Replacement: passo 48, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 48, immagine 2 di 2
    • From the outside of the phone, push the hold switch into the rear case with the point of a spudger.

    • This action will free the hold switch and gasket from the rear case.

  49. iPhone 7 Volume Control Buttons Replacement: passo 49, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 49, immagine 2 di 2
    • Use a pair of tweezers to remove the rear-facing camera.

  50. iPhone 7 Volume Control Buttons Replacement: passo 50, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 50, immagine 2 di 2
    • Moving from power button side of the phone, use an opening pick to separate the adhesive holding the antenna flex cable to the rear case.

  51. iPhone 7 Volume Control Buttons Replacement: passo 51, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 51, immagine 2 di 2
    • Slide the point of an opening pick underneath the antenna flex cable towards the top of the phone, separating the remaining adhesive.

  52. iPhone 7 Volume Control Buttons Replacement: passo 52, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 52, immagine 2 di 2
    • Use tweezers to move the antenna flex cable away from the edge of the phone, freeing the screw bracket from the rear case.

    • Remove the antenna flex cable.

  53. iPhone 7 Volume Control Buttons Replacement: passo 53, immagine 1 di 1
    • Remove the 2.3 mm standoff screw securing the flash bracket to the rear case.

    • Standoff screws are best removed using an [prodotto collegato mancante o disabilitato: IF145-343] and driver handle.

    • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

  54. iPhone 7 Volume Control Buttons Replacement: passo 54, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 54, immagine 2 di 2
    • Remove the flash bracket.

  55. iPhone 7 Volume Control Buttons Replacement: passo 55, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 55, immagine 2 di 2
    • Use the point of a spudger to gently unseat the flash module.

  56. iPhone 7 Volume Control Buttons Replacement: passo 56, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 56, immagine 2 di 2
    • Use the blade of a Halberd spudger to separate the adhesive holding the microphone to the rear case.

  57. iPhone 7 Volume Control Buttons Replacement: passo 57, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 57, immagine 2 di 2
    • Gently fold the power button module from the edge of the rear case.

  58. iPhone 7 Volume Control Buttons Replacement: passo 58, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 58, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 58, immagine 3 di 3
    • Slide the blade of a halberd spudger under the power button end of the button cable to separate it from the adhesive on the rear case.

    • Continue to separate the adhesive by moving the blade towards the top of the phone.

  59. iPhone 7 Volume Control Buttons Replacement: passo 59, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 59, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 59, immagine 3 di 3
    • Continue to move the blade of the halberd spudger underneath the power and volume control cable.

    • Move slowly to make sure that the cable is not damaged during removal.

  60. iPhone 7 Volume Control Buttons Replacement: passo 60, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 60, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 60, immagine 3 di 3
    • Slide the halberd spudger under the volume control portion of the button cable.

    • Gently slide the blade underneath the cable towards the bottom of the phone, separating the remaining adhesive.

  61. iPhone 7 Volume Control Buttons Replacement: passo 61, immagine 1 di 1
    • Remove the power and volume control cable.

  62. iPhone 7 Volume Control Buttons Replacement, Volume Buttons: passo 62, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement, Volume Buttons: passo 62, immagine 2 di 2
    • Pull the volume button clip towards the bottom of the phone to free it from the bracket.

  63. iPhone 7 Volume Control Buttons Replacement: passo 63, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 63, immagine 2 di 2
    • Pull the clip towards the top of the phone to remove it.

  64. iPhone 7 Volume Control Buttons Replacement: passo 64, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 64, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 64, immagine 3 di 3
    • Pull the volume button clip towards the bottom of the phone to free it from the bracket.

    • Pull the clip towards the top of the phone to remove it.

  65. iPhone 7 Volume Control Buttons Replacement: passo 65, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 65, immagine 2 di 2
    • Slide the flat end of a spudger underneath the bottom edge of the volume button bracket.

    • Adjust the spudger so that it can move away from the rear case without contacting the protruding peg that is on the volume button.

    • Rotate the spudger to pop the bracket off of the peg on the volume button.

  66. iPhone 7 Volume Control Buttons Replacement: passo 66, immagine 1 di 2 iPhone 7 Volume Control Buttons Replacement: passo 66, immagine 2 di 2
    • Pull the bracket from the rear case.

  67. iPhone 7 Volume Control Buttons Replacement: passo 67, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 67, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 67, immagine 3 di 3
    • Repeat the procedure to remove the second volume button bracket.

  68. iPhone 7 Volume Control Buttons Replacement: passo 68, immagine 1 di 3 iPhone 7 Volume Control Buttons Replacement: passo 68, immagine 2 di 3 iPhone 7 Volume Control Buttons Replacement: passo 68, immagine 3 di 3
    • Use the pointed end of a spudger to push each of the volume button covers out of the rear case.

    • Remove the volume button covers.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 31 persone hanno completato questa guida.

Scott Havard

Membro da: 06/27/16

49.564 Reputazione

31 Guide realizzate

10 Commenti

Removing the battery is excluded from this repair.

Josh M - Replica

R u able to fix water damage

alex - Replica

Hi r u able to fix water damage for iPhone 7

alex - Replica

Hi Alex, the repairability of water damage varies hugely depending on your unique circumstances, but this guide is a good place to start. If the damage is extensive you may want to take your phone to a local repair professional.

Adam O'Camb -

Bonjour je voudrais savoir si vous avais la même explication mais pour iPhone 7+ s’il vous plaît ??

Lydia David - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 7

Ultimi 7 Giorni: 39

Ultimi 30 Giorni: 230

Tutti i Tempi: 55,822