Aggiusta la tua roba

Diritto alla Riparazione

Store

iPhone 7 Logic Board Disconnection

Scritto Da: Evan Noronha (e 4 altri collaboratori)
  • Commenti: 23
  • Preferiti: 0

Difficoltà

Moderato

Passi

13

Tempo Necessario

Suggerisci un tempo??

Sezioni

1

Contrassegni

1

Prerequisite Only

Solo Prerequisita

Per favore tieni conto che questa guida è solo un prerequisito per altre guide.

Introduzione

prereq only

  1. Use the flat end of a spudger to disconnect the rear-facing camera connector. Use the flat end of a spudger to disconnect the rear-facing camera connector.

    • Use the flat end of a spudger to disconnect the rear-facing camera connector.

    Traduci

  2. Remove the following Phillips screws securing the rear camera bracket to the rear case: One 1.3 mm screw

    • Remove the following Phillips screws securing the rear camera bracket to the rear case:

    • One 1.3 mm screw

    • One 2.5 mm screw

    Traduci

  3. Remove the bracket.

    • Remove the bracket.

    Traduci

  4. Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module. Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module.

    • Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module.

    Traduci

  5. Remove the two 1.2 mm tri-point screws securing the upper cable bracket.

    • Remove the two 1.2 mm tri-point screws securing the upper cable bracket.

    Traduci

  6. The Essential Toolkit

    The most helpful tools in our most compact kit.

    Acquista ora

    The Essential Toolkit

    The most helpful tools in our most compact kit.

    Acquista ora

  7. Remove the upper cable bracket. Remove the upper cable bracket.

    • Remove the upper cable bracket.

    Traduci

  8. Use the flat end of a spudger to disconnect the upper cable connector. Use the flat end of a spudger to disconnect the upper cable connector.

    • Use the flat end of a spudger to disconnect the upper cable connector.

    Traduci

  9. Remove the Phillips screws securing the Wi-Fi antenna: Three 1.2 mm screws

    • Remove the Phillips screws securing the Wi-Fi antenna:

    • Three 1.2 mm screws

    • One 1.7 mm screw

    Traduci

  10. Remove the top left antenna. Remove the top left antenna.

    • Remove the top left antenna.

    Traduci

  11. Remove the following Phillips screws:

    • Remove the following Phillips screws:

    • One 1.3 mm screw

    • One 2.2 mm screw

    Traduci

  12. Remove the bracket. Remove the bracket.

    • Remove the bracket.

    Traduci

  13. Remove the 2.2 mm standoff screw from the grounding bracket.

    • Remove the 2.2 mm standoff screw from the grounding bracket.

    • Standoff screws are best removed using an [prodotto collegato mancante o disabilitato: IF145-343-1] and driver handle.

    • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

    Traduci

  14. Use tweezers to gently bend the logic board grounding bracket out of the way. Use tweezers to gently bend the logic board grounding bracket out of the way.

    • Use tweezers to gently bend the logic board grounding bracket out of the way.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 4 altri collaboratori

Evan Noronha

Membro da: 05/02/2015

200.567 Reputazione

178 Guide realizzate

Distintivi: 49

+46 altri distintivi

Team

iFixit Membro di iFixit

Community

132 Membri

13.477 Guide realizzate

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 113