Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Rimuovi le due viti Pentalobe P2 da 3,4 mm sul lato inferiore dell'iPhone, su entrambi i lati del connettore Lightning.
-
-
-
Tira la manopola blu verso la cerniera per sbloccare i bracci dell'Anti-Clamp.
-
Fai scorrere le braccia o sul bordo sinistro o su quello destro del tuo iPhone.
-
Posiziona le ventose sullo schermo, subito sopra il tasto Home, una davanti e una sul retro.
-
Premi le ventose cosรฌ che facciano presa sull'area desiderata.
-
-
-
Allontana la manopola blu dalla cerniera per bloccare le braccia
-
Ruota la manopola in senso orario di 360 gradi o finchรฉ vedi che la ventosa comincia ad allungarsi.
-
Aspetta un minuto per dare la possibilitร all'adesivo di lasciarsi andare e alla parte inferiore dello schermo di aprirsi.
-
Salta i prossimi tre passi.
-
-
-
Se non hai un Anti-Clamp, segui i prossimi tre passaggi su come utilizzare una ventosa.
-
In alternativa, scalda moderatamente il bordo inferiore dell'iPhone usando un iOpener o un asciugacapelli per circa un minuto.
-
-
-
Afferra con delicatezza il gruppo display e sollevalo verso l'alto per aprire il telefono, usando le clip nella parte alta del pannello anteriore come una cerniera.
-
Apri il display a un angolo di circa 90ยฐ e appoggialo contro qualche cosa per tenerlo sollevato mentre tu lavori sul telefono.
-
Usa anche un elastico per tenere il display in una posizione sicura mentre lavori. In questo modo eviterai di forzare i cavi del display.
-
-
Attrezzo utilizzato in questo passaggio:Magnetic Project Mat$19.95
-
Rimuovi le due viti a croce Phillips che fissano la staffa del connettore della batteria:
-
Una vite da 2,9 mm
-
Una vite da 2,2 mm
-
-
-
Rimuovi le seguenti quattro viti a croce Phillips che fissano la staffa del cavo del display:
-
Tre viti da 1,2 mm
-
Una vite da 2,8 mm
-
-
-
Usa l'estremitร piatta di uno spudger per scollegare la fotocamera iSight dal suo zoccolo sulla scheda logica.
-
-
-
-
Inserisci uno strumento di estrazione SIM o una graffetta nel piccolo foro nel vassoio della scheda SIM.
-
Premi per espellere la SIM.
-
-
-
Rimuovi le due viti a croce Phillips da 2,3 mm che fissano la staffa del connettore superiore del cavo.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the two 1.5 mm Phillips screws holding the Taptic Engine in place.
-
Remove the Taptic Engine.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use tweezers to peel up the tips of the battery adhesive strips at the lower edge of the battery.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Pull one of the adhesive strips straight out, towards the bottom of the iPhone.
-
For best results, pull the strip at a 60ยบ angle or less.
-
Continue pulling until the strip is fully removed.
-
If one of the adhesive strips breaks under the battery during this procedure, and cannot be retrieved, remove the remaining strip, and then skip to Step 48.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Repeat the previous step for the second adhesive strip.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
Attrezzo utilizzato in questo passaggio:Plastic Cards$2.99-
If you successfully removed all three adhesive strips, move on to the next step. Otherwise, you will need to pry the battery from the rear case.
-
Prepare an iOpener and apply it to the back of the rear case, directly over the battery. Alternatively, you can apply heat using a heat gun or hair dryer.
-
After about a minute, flip the phone over and use a plastic card to break up any remaining adhesive behind the battery.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the single 1.3 mm Phillips screw securing the flash bracket.
-
Remove the flash bracket.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to lift the flash out of its housing in the rear case.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the following five Phillips screws:
-
Two 2.5 mm screws set into the left edge of the rear case
-
One 2.1 mm Phillips #000 screw set into the left edge of the rear case
-
Two 2.1 mm screws set into the right edge of the rear case
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use the pointed tip of a spudger to gently separate the microphone from the rear case.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Slide an opening pick between the upper component cable and the rear case.
-
Gently separate the cable from the rear case.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Continue pushing the opening pick under the cable until it fully separates from the rear case.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the upper component cable assembly.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
If your replacement part did not come with the mute switch cover, you will need to remove the switch cover and transfer It.
-
Use the flat end of the spudger to press down and hold the old bracket firmly in place.
-
Use tweezers or your fingers to carefully rock the switch cover such that the switch cover pins swing out of their clips.
-
Lift the switch cover straight up.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Grasp the metal bar behind either of the two volume control button covers, and pull the button cover out of its housing in the rear case.
-
Repeat for the second volume control button cover.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Grasp the metal bar on the back of the power button cover.
-
Remove the power button cover.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Deroute the antenna cable from its rubber sleeve on the right edge of the rear case.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the antenna cable from the metal clip on the right edge of the rear case.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the following five Phillips screws securing the speaker to the rear case:
-
Two 2.6 mm screws
-
Two 2.3 mm screws
-
One 3.0 mm screw
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use your fingers to lift the speaker out of its housing in the rear case.
-
Remove the speaker assembly.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the following eight Phillips screws:
-
Two 2.9 mm screws securing the headphone jack
-
One 3.7 mm screw securing the microphone bracket
-
Two 1.3 mm screws on the lower edge of the iPhone
-
Two 1.9 mm screws on either side of the Lighting connector
-
One 3.0 mm screw to the left of the connector
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Insert an opening pick between the Lightning connector assembly and the rear case to begin breaking up the adhesive holding the flex cable in place.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to continue separating the Lightning connector assembly from the rear case.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use the tip of a spudger to separate the two microphones from the lower edge of the rear case.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the Lightning connector and headphone jack assembly.
-
Annulla: non ho completato questa guida.
Altre 88 persone hanno completato questa guida.
8 Commenti
I can't get the phillips 000 screw out on step 52, now it's become too hollow within to open. What do I do?
Stripped screws are the worst! We have a guide on how to remove stripped screws that you may find helpful. Remember to maintain lots of pressure on the screw and stop applying force and try a different method if the bit is still slipping.
Every thing works fine except I have no sound, either on speakerphone or normally. Did I break the upper component cable? I've checked all the plug connections and they seem ok.
I have no sound at all from the normal speaker or in speakerphone mode. I have good cellular and Wi-Fi connections and the phone sees to work perfectly otherwise. The battery charges fine through the Lightning connector. Can't use it as a phone though! Did I break the upper component cable in the disassembly? Any other ideas?