Aggiusta la tua roba Comunità Store

iPhone 6s Plus Taptic Engine Replacement

Introduzione

Follow this guide to replace the Taptic Engine in your iPhone 6s Plus. The Taptic Engine is the iPhone's vibrating and haptic feedback motor. If your phone isn't vibrating or produces a rattling sound when it does, replacing the Taptic Engine can remedy your issues.

Cosa ti serve

Panoramica Video

  1. iPhone 6s Plus Taptic Engine Replacement, Pentalobe Screws: passo 1, immagine 1 di 1

    • Before disassembling your iPhone, discharge the battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

    • Power off your iPhone before beginning disassembly.

    • Remove the two 3.4 mm Pentalobe screws on either side of the Lightning port.

    Traduci

  2. iPhone 6s Plus Taptic Engine Replacement, Opening Procedure: passo 2, immagine 1 di 1
    Attrezzo utilizzato in questo passaggio:
    Anti-Clamp
    $24.95
    Compra

    • If you don't have an Anti-Clamp, follow the next three steps to use a suction handle.

    • Apply mild heat to the lower edge of the iPhone using an iOpener or hair dryer for about a minute.

    • Heat softens the adhesive securing the display, making it easier to open.

    Traduci

  3. iPhone 6s Plus Taptic Engine Replacement: passo 3, immagine 1 di 1

    • Opening the display on the 6s Plus separates a thin strip of adhesive around the perimeter of the display. If you prefer to replace the adhesive, have a set of new adhesive strips ready before you continue. It's possible to complete the repair without replacing the adhesive, and you probably won't notice any difference in functionality.

    • Apply a suction cup to the lower left corner of the display assembly.

    • If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.

    Traduci

  4. iPhone 6s Plus Taptic Engine Replacement: passo 4, immagine 1 di 2 iPhone 6s Plus Taptic Engine Replacement: passo 4, immagine 2 di 2

    • Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.

    • Pulling too hard may damage the display assembly. Apply just enough pressure to create a small gap between the display assembly and the rear case.

    Traduci

  5. iPhone 6s Plus Taptic Engine Replacement: passo 5, immagine 1 di 3 iPhone 6s Plus Taptic Engine Replacement: passo 5, immagine 2 di 3 iPhone 6s Plus Taptic Engine Replacement: passo 5, immagine 3 di 3

    • The safest place to pry from is the notch in the front panel above the headphone jack.

    • While still maintaining pressure on the suction cup, insert the flat tip of a spudger into the gap, directly above the headphone jack.

    Traduci

  6. iPhone 6s Plus Taptic Engine Replacement: passo 6, immagine 1 di 2 iPhone 6s Plus Taptic Engine Replacement: passo 6, immagine 2 di 2

    • Twist the spudger to widen the gap between the front panel and the rear case.

    Traduci

  7. iPhone 6s Plus Taptic Engine Replacement: passo 7, immagine 1 di 3 iPhone 6s Plus Taptic Engine Replacement: passo 7, immagine 2 di 3 iPhone 6s Plus Taptic Engine Replacement: passo 7, immagine 3 di 3

    • While firmly pulling up on the suction cup, slide the edge of the spudger under the bottom left corner of the display.

    Traduci

  9. iPhone 6s Plus Taptic Engine Replacement: passo 8, immagine 1 di 2 iPhone 6s Plus Taptic Engine Replacement: passo 8, immagine 2 di 2

    • Slide the tip of the spudger up the left side of the phone, between the front panel and the rear case.

    Traduci

  10. iPhone 6s Plus Taptic Engine Replacement: passo 9, immagine 1 di 2 iPhone 6s Plus Taptic Engine Replacement: passo 9, immagine 2 di 2

    • Insert the flat tip of the spudger under the right edge of the display.

    • Slide the spudger up the right side.

    Traduci

  11. iPhone 6s Plus Taptic Engine Replacement: passo 10, immagine 1 di 2 iPhone 6s Plus Taptic Engine Replacement: passo 10, immagine 2 di 2

    • Use a plastic opening tool to hold down the rear case while pulling up the suction cup to open the phone.

    • Do not remove the display completely, or you will damage the data cables connecting the display near the top edge of the iPhone.

    Traduci

  12. iPhone 6s Plus Taptic Engine Replacement: passo 11, immagine 1 di 2 iPhone 6s Plus Taptic Engine Replacement: passo 11, immagine 2 di 2

    • Pull up on the small nub on the suction cup to remove it from the display.

    Traduci

  13. iPhone 6s Plus Taptic Engine Replacement: passo 12, immagine 1 di 3 iPhone 6s Plus Taptic Engine Replacement: passo 12, immagine 2 di 3 iPhone 6s Plus Taptic Engine Replacement: passo 12, immagine 3 di 3

    • Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.

    • Open the display to about a 90º angle, and lean it against something to keep it propped up while you're working on the phone.

    • Don't open the display more than 90º—it is still connected to the top of the phone by the display, digitizer, and front camera cables which can tear easily.

    • Add a rubber band to keep the display securely in place while you work. This prevents undue strain on the display cables.

    • In a pinch, you can use an unopened canned beverage to support the display.

    Traduci

  14. iPhone 6s Plus Taptic Engine Replacement, Battery Connector: passo 13, immagine 1 di 1
    Attrezzo utilizzato in questo passaggio:
    Magnetic Project Mat
    $19.95
    Compra

    • Remove two Phillips screws securing the battery connector bracket to the logic board, of the following lengths:

    • One 2.9 mm screw

    • One 2.3 mm screw

    • Throughout this guide, keep careful track of your screws so that each one goes back where it came from during reassembly. Installing a screw in the wrong place can cause permanent damage.

    Traduci

  15. iPhone 6s Plus Taptic Engine Replacement: passo 14, immagine 1 di 2 iPhone 6s Plus Taptic Engine Replacement: passo 14, immagine 2 di 2

    • Remove the battery connector bracket.

    Traduci

  16. iPhone 6s Plus Taptic Engine Replacement: passo 15, immagine 1 di 3 iPhone 6s Plus Taptic Engine Replacement: passo 15, immagine 2 di 3 iPhone 6s Plus Taptic Engine Replacement: passo 15, immagine 3 di 3

    • Use a spudger or a clean fingernail to disconnect the battery connector by prying it straight up off the logic board.

    Traduci

  17. iPhone 6s Plus Taptic Engine Replacement: passo 16, immagine 1 di 3 iPhone 6s Plus Taptic Engine Replacement: passo 16, immagine 2 di 3 iPhone 6s Plus Taptic Engine Replacement: passo 16, immagine 3 di 3

    • Bend the connector back to ensure it doesn't make contact and power the iPhone on while you're working on it.

    Traduci

  18. iPhone 6s Plus Taptic Engine Replacement, Taptic Engine: passo 17, immagine 1 di 1

    • Remove the following Phillips screws over the Taptic Engine cable bracket:

    • Two 3.5 mm screws

    • One 2.7 mm screw

    Traduci

  19. iPhone 6s Plus Taptic Engine Replacement: passo 18, immagine 1 di 2 iPhone 6s Plus Taptic Engine Replacement: passo 18, immagine 2 di 2

    • Remove the Taptic Engine cable bracket.

    Traduci

  20. iPhone 6s Plus Taptic Engine Replacement: passo 19, immagine 1 di 2 iPhone 6s Plus Taptic Engine Replacement: passo 19, immagine 2 di 2

    • Disconnect the Taptic Engine's flex cable from the socket on the Lightning Connector flex cable.

    Traduci

  21. iPhone 6s Plus Taptic Engine Replacement: passo 20, immagine 1 di 1

    • Remove the following two Phillips screws:

    • One 3.1 mm screw

    • One 2.1 mm screw

    Traduci

  22. iPhone 6s Plus Taptic Engine Replacement: passo 21, immagine 1 di 2 iPhone 6s Plus Taptic Engine Replacement: passo 21, immagine 2 di 2

    • Remove the Taptic Engine.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 28 persone hanno completato questa guida.

Autore

con 6 altri collaboratori

Dante Mazzanti

Membro da: 07/13/15

36.174 Reputazione

26 Guide realizzate

Distintivi: 34

+31 altri distintivi

2 Commenti

Great! Was able to replace my wife’s engine which started to be very buzzy for some reason.

Eddie Wang - Replica

Excelente, gracias!!

eldios776 - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 6

Ultimi 7 Giorni: 21

Ultimi 30 Giorni: 92

Tutti i Tempi: 27,117