Aggiusta la tua roba Comunità Store

iPhone 6s Plus Speaker Replacement

Solo Prerequisita
Questa guida è destinata a essere usata solo come prerequisito per altre guide. Da sola è incompleta.

Introduzione

Prerequisite guide only! Speaker module replacement for the iPhone 6s Plus. Updated version which contains photos that have the logic board intact.

Cosa ti serve

  1. iPhone 6s Plus Speaker Replacement, Speaker: passo 1, immagine 1 di 2 iPhone 6s Plus Speaker Replacement, Speaker: passo 1, immagine 2 di 2

    • Use the point of a spudger to pry up and disconnect the antenna cable from the bottom of the logic board.

    Traduci

  2. iPhone 6s Plus Speaker Replacement: passo 2, immagine 1 di 2 iPhone 6s Plus Speaker Replacement: passo 2, immagine 2 di 2

    • Use the point of a spudger to pry up and disconnect the Lightning connector cable from the logic board.

    Traduci

  3. iPhone 6s Plus Speaker Replacement: passo 3, immagine 1 di 2 iPhone 6s Plus Speaker Replacement: passo 3, immagine 2 di 2

    • Remove the three Phillips screws securing the Lightning connector bracket:

    • Two 3.5 mm screws

    • One 2.7 mm screw

    • Remove the bracket.

    Traduci

  5. iPhone 6s Plus Speaker Replacement: passo 4, immagine 1 di 2 iPhone 6s Plus Speaker Replacement: passo 4, immagine 2 di 2

    • Use the point of a spudger to pry up and disconnect the antenna cable from the Lightning connector assembly.

    Traduci

  6. iPhone 6s Plus Speaker Replacement: passo 5, immagine 1 di 2 iPhone 6s Plus Speaker Replacement: passo 5, immagine 2 di 2

    • Use the point of a spudger to pry up and disconnect the antenna cable from the top of the logic board.

    Traduci

  7. iPhone 6s Plus Speaker Replacement: passo 6, immagine 1 di 3 iPhone 6s Plus Speaker Replacement: passo 6, immagine 2 di 3 iPhone 6s Plus Speaker Replacement: passo 6, immagine 3 di 3

    • Carefully lift the antenna cable and de-route it from the edge of the phone. Use the point of a spudger to help lift the cable free it from the retaining clips.

    • If the cable does not have enough room to lift up, loosen this Phillips screw securing the logic board so that the board can give more wiggle room.

    • Be sure to re-tighten this screw during re-installation.

    • During re-installation, be sure to route the antenna cable underneath the logic board corner.

    • During re-installation, you can also re-insert the SIM card tray after re-routing the antenna cable.

    • If you feel any resistance, stop and make sure that the tray isn't snagging the antenna cable.

    Traduci

  8. iPhone 6s Plus Speaker Replacement: passo 7, immagine 1 di 2 iPhone 6s Plus Speaker Replacement: passo 7, immagine 2 di 2

    • Remove the six Phillips screws securing the speaker to the rear case:

    • One 2.5 mm screw

    • Two 2.7 mm screws

    • One 1.5 mm screw

    • One 1.7 mm screw

    • One 2.6 mm screw securing the speaker to the bottom edge of the rear case.

    Traduci

  9. iPhone 6s Plus Speaker Replacement: passo 8, immagine 1 di 3 iPhone 6s Plus Speaker Replacement: passo 8, immagine 2 di 3 iPhone 6s Plus Speaker Replacement: passo 8, immagine 3 di 3

    • Insert the flat end of a spudger between the long edge of the speaker module and the case wall.

    • Pry gently to loosen the speaker module.

    • Once the module is loose, lift and remove the speaker module and the attached antenna cable from the phone.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 1 altro collaboratore

Arthur Shi

Membro da: 01/03/18

249.876 Reputazione

503 Guide realizzate

Distintivi: 47

+44 altri distintivi

Team

iFixit Membro di iFixit

Staff

135 Membri

16.734 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 150