Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Spegni il tuo iPhone prima di iniziare lo smontaggio.
-
La cover posteriore del telefono potrebbe avere due viti a croce Phillips #000 o viti "Pentalobe" a 5 punte di Apple. Controlla quali viti hai e assicurati di avere anche il cacciavite corretto per rimuoverle.
-
Rimuovi le due viti Pentalobe o Phillips #000 da 3,6 mm accanto al connettore dock.
-
-
-
Rimuovi la singola vite a croce Philips da 1,5 mm che fissa il connettore della batteria alla scheda madre (se presente).
-
-
-
Solleva la linguetta di plastica trasparente esposta per staccare la batteria dall'adesivo che la fissa all'iPhone.
-
Se è rimasta della soluzione alcolica nel telefono, puliscilo con cura o lascialo asciugare all'aria prima di installare la nuova batteria.
-
Rimuovi la batteria.
-
Prima del riassemblaggio, pulisci i punti di contatto metallo su metallo con uno sgrassante come windex. Gli oli delle dita possono potenzialmente causare problemi di interferenza wireless.
-
Esegui un hard reset dopo il rimontaggio. Ciò può prevenire diversi problemi e semplificare la risoluzione dei problemi.
-
-
-
Rimuovi le due viti a croce Phillips da 1,8 mm che fissano il cavo del connettore dock alla scheda logica.
-
Rimuovi la sottile copertura del cavo del connettore dock in metallo.
-
-
-
-
Rimuovi le seguenti cinque viti:
-
Tre viti a croce Phillips da 1,3 mm
-
Una vite a croce Phillips da 1,5 mm
-
Una vite a croce Phillips da 2,4 mm
-
-
-
Scollega i cinque cavi vicino alla parte superiore della scheda logica nel seguente ordine:
-
Cavo jack per cuffie/pulsante del volume
-
Cavo del pulsante di accensione
-
Cavo della fotocamera frontale
-
Cavo digitalizzatore
-
Cavo dati display
-
Per scollegare i cavi, usa il bordo di uno strumento di apertura in plastica per sollevare delicatamente i connettori verso l'alto e fuori dalle prese sulla scheda logica.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 2.0 mm Phillips screws securing the power button bracket to the outer case.
-
Slightly pull the power button bracket away from the outer case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a pair of tweezers to remove the power button from the iPhone.
-
Annulla: non ho completato questa guida.
Altre 74 persone hanno completato questa guida.
6 Commenti
If you look at the Logic Board, the top kind of looks like steps. Find the tallest point, the go left and down one step. The piece goes at the top of this. The thinner part should face towards the back of the phone. It is to protect the LCD cable.
Hello! New to this comment section and love it compared to the YouTube videos that always seem to have the wrong phone... I have a Verizon CDMA iPhone 4 (not 4s). I'm having a problem with the power button. I have changed the ribbon and the button still won't click. I have checked the ribbon button with a pointed screwdriver and it clicks like it should. For example, if I did not put the metal/physical button back into the phone, it would see that I could just poke something inside to turn on and off. Is there a "spring" to the physical button? Do I have something missing? The button seems as it is in the diagrams and I wonder if the wire on the bottom of the button is supposed to provide a springing of some sort...to allow for it to "stay tall" and away from the bubble button on the ribbon. Then when the physical button is pushed it will go down and activate or push the ribbon button, and then click or spring back up. Am I missing something here? Tks GANDL2123@gmail.com
If someone tells you or you figure it out,can you tell me at dima_fedorov@yahoo.com,or just reply on this.
dima -
"the outward edges should be on top"... what? I have the iphone 4 Verizon and I've followed the instructions to the letter. I have installed the power button with the metal wire thing down towards the screen...the button slides in nicely and I have replaced the new ribbon cable with the copper button on it new and when I test the copper button on the cable itself it does click...but when installed I can't get the button to spring in and out and click like it is supposed to. What am I doing wrong...? Tks to gandL2123@gmail.com. Augusta, GA