Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Se il vetro del tuo schermo è rotto, applica del nastro adesivo per prevenire ulteriori rotture ed evitare di ferirti durante la riparazione.
-
Applica delle strisce sovrapposte di nastro adesivo trasparente sul display dell'iPhone fino a coprire l'intero schermo.
-
-
-
Rimuovi le due viti a croce Phillips #00 da 3,7 mm dall'estremità del connettore dock dell'iPhone.
-
-
-
Usa uno spudger per sollevare la linguetta di plastica bianca che tiene in posizione il cavo a nastro "3". La linguetta bianca ruoterà verso l'alto di 90 gradi, rilasciando il cavo a nastro.
-
Fai scorrere il cavo a nastro nero fuori dal connettore e rimuovi il gruppo display dall'iPhone.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert your SIM eject tool or a paper clip into the hole next to the headphone jack.
-
Press down on the tool until the SIM card tray pops out.
-
Grasp the SIM card tray and slide it out of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the ribbon cable labeled "4."
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the ribbon cable labeled "5."
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the ribbon cable labeled "6."
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 8 screws:
-
Five 2.3 mm Phillips #00 screws with partial threads securing the logic board to the rear case.
-
Two 2.3 mm Phillips #00 screws with full threads securing the logic board and camera.
-
One 2.9 mm Phillips #00 screw from beneath the "Do not remove" sticker.
-
Note for re-assembly:
-
The screw that goes next to the camera (bottom right orange highlighted screw) also has a metal strip that holds the camera in place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to gently pry the camera up and out of its housing in the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to gently pry up the end of the logic board closest to the dock connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the logic board towards the dock connector and out of the iPhone.
-
When replacing the logic board after installing battery, connect the camera to the logic board before inserting it into the case. Then make sure to set the top section of the logic board (where the SIM tray is) in place before settling the rest of the board in place. This is important, as sometimes the SIM card slot will not align into place. Once the top section is in place, the bottom section can be maneuvered into place. You will know the logic board is correctly installed when the SIM tray is aligned with the opening in the iPhone case and the camera module seats neatly into its place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to pry the battery up from the rear case. The battery is attached with an adhesive strip around the perimeter of the battery.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following four screws:
-
Three 1.8 mm Phillips #00 screws securing the headphone jack and GPS antenna to the rear panel.
-
One 3.8 mm Phillips #00 screw in the plastic loop near the headphone jack.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four Phillips #00 screws securing the volume and vibrate buttons.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the volume button circuitry away from the side of the iPhone, and carefully peel up the orange ribbon cable from the rear panel.
-
Carefully pull the headphone jack away from the top edge of the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently pull the headphone jack electronics away from the side of the rear panel to reveal the plastic mute switch.
-
Annulla: non ho completato questa guida.
Altre 75 persone hanno completato questa guida.
2 Commenti
if you are having an issue with the mute function, where you slightly press on the face plate and it flip flops between mute and unmute,if your mute button is not visualy damaged it may be just a loose connector. Check ribbon connector 5 after step 3. If it was loose secure it and reconect and close the Phone. this should solve your issue. Connector 5 is the conection for the mute button as well as the volume control buttons.
When you buy a replacement mute switch button, it doesn't come with this little piece of padding / foam in it. Assuming that the original piece of padding / foam is not available, what padding / foam can you use to put in that mute button opening? What is it called? Where can you buy it?