Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Introduzione
La batteria non dura a lungo? Cambiala.
Cosa ti serve
Panoramica Video
-
-
Se il vetro del tuo schermo รจ rotto, applica del nastro adesivo per prevenire ulteriori rotture ed evitare di ferirti durante la riparazione.
-
Applica delle strisce sovrapposte di nastro adesivo trasparente sul display dell'iPhone fino a coprire l'intero schermo.
-
-
-
Rimuovi le due viti a croce Phillips #00 da 3,7 mm dall'estremitร del connettore dock dell'iPhone.
-
-
-
-
Usa uno spudger per sollevare la linguetta di plastica bianca che tiene in posizione il cavo a nastro "3". La linguetta bianca ruoterร verso l'alto di 90 gradi, rilasciando il cavo a nastro.
-
Fai scorrere il cavo a nastro nero fuori dal connettore e rimuovi il gruppo display dall'iPhone.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Insert your SIM eject tool or a paper clip into the hole next to the headphone jack.
-
Press down on the tool until the SIM card tray pops out.
-
Grasp the SIM card tray and slide it out of the iPhone.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the ribbon cable labeled "4."
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the ribbon cable labeled "5."
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the ribbon cable labeled "6."
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the following 8 screws:
-
Five 2.3 mm Phillips #00 screws with partial threads securing the logic board to the rear case.
-
Two 2.3 mm Phillips #00 screws with full threads securing the logic board and camera.
-
One 2.9 mm Phillips #00 screw from beneath the "Do not remove" sticker.
-
Note for re-assembly:
-
The screw that goes next to the camera (bottom right orange highlighted screw) also has a metal strip that holds the camera in place.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use a spudger to gently pry the camera up and out of its housing in the rear case.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use a spudger to gently pry up the end of the logic board closest to the dock connector.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Slide the logic board towards the dock connector and out of the iPhone.
-
When replacing the logic board after installing battery, connect the camera to the logic board before inserting it into the case. Then make sure to set the top section of the logic board (where the SIM tray is) in place before settling the rest of the board in place. This is important, as sometimes the SIM card slot will not align into place. Once the top section is in place, the bottom section can be maneuvered into place. You will know the logic board is correctly installed when the SIM tray is aligned with the opening in the iPhone case and the camera module seats neatly into its place.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use a spudger to pry the battery up from the rear case. The battery is attached with an adhesive strip around the perimeter of the battery.
-
Per riassemblare il dispositivo, segui queste istruzioni in ordine inverso.
Per riassemblare il dispositivo, segui queste istruzioni in ordine inverso.
Annulla: non ho completato questa guida.
Altre 2453 persone hanno completato questa guida.
Un ringraziamento speciale a questi traduttori:
100%
Questi traduttori ci stanno aiutando ad aggiustare il mondo! Vuoi partecipare?
Inizia a tradurre ›
97 Commenti
pay close attention to the pictures
use a business card type refrigerator magnet to keep the screws in order and to keep them from being lost. Its hard to see the black plastic latch that retains the ribbon number 3, it simply flips up toward the top of the phone. go slow and methodical.when reinstalling insert the Sim card holder before replacing all the screws, it helps to hold the board in the proper place.
GREAT tip about the flat fridge magnet to lay out and hold the screws as you take them out. I would have certainly dropped a screw or mixed them up if I'd not used this tip.
mattfife -
Agree totally, very important guideline! Also, have a tweezer handy.
xint -
There is a tiny metal clip that holds the camera down on my iPhone 3GS. It fell out after I had removed the screw that holds the camera in place, as directed. Only intuition and good luck allowed me to figure out where it had come from.
I also found out that the connector for my camera came loose from the BACK of the logic board. it snapped back in place, no problem, but I could have easily tried reassembling the phone without it connected, and either found things didn't want to fit, or ended up without a functioning camera, and a panic attack that I had clumsily destroyed same.
Hi. The little metal clip that holds the camera fell out for me too. Where exactly do you reinstall it and how does it line up? Thanks.