Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Se il vetro del tuo schermo è rotto, applica del nastro adesivo per prevenire ulteriori rotture ed evitare di ferirti durante la riparazione.
-
Applica delle strisce sovrapposte di nastro adesivo trasparente sul display dell'iPhone fino a coprire l'intero schermo.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two Phillips #00 screws from the dock-connector end of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the metal handle from the suction cup. It's easier and safer to grip the suction cup's base instead of the metal handle.
-
Use a small suction cup near the Home button to gently pull up the bottom portion of the iPhone's display assembly.
-
If the display assembly is too damaged to allow the suction cup to adhere, tape with a strong adhesive such as duct tape, or thick, clear packing tape may be used.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the display assembly up until it is at an angle of approximately 45 degrees.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Continue to hold the display assembly with one hand, and use your other hand and a spudger to disconnect the black ribbon cable labeled "1."
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the display assembly up until it is roughly vertical. This will allow easier access for disconnecting the remaining cables.
-
Use a spudger to disconnect the black ribbon cable labeled "2."
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to flip up the white plastic tab holding the remaining ribbon cable in place. The white tab will rotate up 90 degrees, releasing the ribbon cable.
-
Slide the black ribbon cable out of its connector, and remove the display assembly from the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert your SIM eject tool or a paper clip into the hole next to the headphone jack.
-
Press down on the tool until the SIM card tray pops out.
-
Grasp the SIM card tray and slide it out of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the ribbon cable labeled "4."
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the ribbon cable labeled "5."
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the ribbon cable labeled "6."
-
If you have an iPhone 3GS, refer to picture 2 and use a spudger to disconnect the ribbon cable labeled "7."
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully peel up the small sticker labeled "Do not remove."
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 8 screws:
-
Five 2.3 mm Phillips #00 screws with partial threads securing the logic board to the rear panel.
-
Two 2.3 mm Phillips #00 screws with full threads securing the logic board and camera.
-
One 2.9 mm Phillips #00 screw from beneath the "Do not remove" sticker.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to gently remove the camera retaining clip, (formerly secured by the removed screw) and gently pry the camera up and out of its housing in the rear panel. The camera cannot be removed entirely yet because it's connected to the bottom of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to gently pry up the end of the logic board closest to the dock connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the logic board towards the dock connector and out of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the camera from the logic board.
-
Annulla: non ho completato questa guida.
Altre 102 persone hanno completato questa guida.
5 Commenti
Step 6: When I attempted to 'rotate the white connector 90 degrees' my white connector broke into 4 pieces... my phone is now beyond my repair. I feel soo dumb. I should have used a pair of eyebrow tweezers (two flat blades that press together) to wiggle the #3 ribbon cable in/out of the connector instead of trying to pivot it.
Anyone know how to repair this? Drop me a line at quathiaski(at)gmail.com
I have found out why I broke my connector all to heck... I attacked the wrong end with my plastic prodder. Work on the BLACK end... it moves...not the white end.
Dayna -
Wow… I don't know!!
You have to search for used parts in marketplace like eBay and so on.
It's the only way I know, I'm sorry.