Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Inserisci uno strumento di espulsione della scheda SIM o una graffetta nel foro accanto al jack delle cuffie.
-
Premi sull'attrezzo finché il vassoio della scheda SIM non fuoriesce.
-
-
-
Inserisci uno strumento di apertura per iPod nello spazio tra il coperchio dell'antenna e il frontalino. Il cuneo dello strumento dovrebbe puntare verso la cover dell'antenna. Fai scorrere lo strumento attorno all'angolo e verso l'alto fino a raggiungere il supporto metallico.
-
Ripeti la stessa procedura sull'altro lato del connettore dock.
-
-
-
Rimuovi le tre viti a croce Phillips #00 che fissano il pannello posteriore all'iPhone.
-
-
-
-
Solleva il pannello posteriore tirando lo scovolino in senso orario con un movimento rapido. Applica una forza perpendicolare al piano del gruppo schermo. Potresti aver paura ad andare veloce, ma procedendo lentamente è più facile che la custodia si pieghi.
-
Il pannello posteriore è ancora collegato all'iPhone tramite il cavo del jack delle cuffie, quindi non rimuovere ancora completamente il pannello posteriore dall'iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel up the orange tape securing the white antenna cable to the side of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the two antenna cables from the communications board. Apple used a small dab of glue on these connections, which may make removing the antenna connections harder.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 3 screws:
-
One Phillips #00 screw securing the logic board to the iPhone near the camera.
-
Two Phillips #00 screws, one on either corner of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the camera connector.
-
Lift the camera out of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Working from the edge opposite the battery connectors, insert a spudger between the battery and the plastic frame and pry up on the battery. It is attached to the casing with an adhesive, but should slowly come free.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide a spudger beneath the logic board on the side opposite the battery connector and pry up slightly. Don't lift up too far, because there are still four attached connectors on the bottom of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
In a similar manner, slide a spudger beneath the logic board where the camera was. Again, don't lift up too far yet as there are still four attached connectors on the bottom of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift up the logic board slightly and slide a spudger beneath the logic board to disconnect the display ribbon cable.
-
After freeing the first connector, slide the spudger further towards the battery and the center of the iPhone to disconnect the speaker connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Go to the other side of the logic board and use a spudger to disconnect the touch sensor cable on the under side of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide a spudger beneath the black locking bar and pry up to rotate the bar 90 degrees (the bar is already rotated in the picture).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Hold both the battery and the logic board assembly and slide both parts away from the orange antenna and out of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three Phillips #00 screws securing the front bezel to the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the iPhone 90 degrees and remove the two Phillips #00 screws from the bottom of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the iPhone 90 degrees and remove the three Phillips #00 screws from the side of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the iPhone 90 degrees and remove the two Phillips #00 screws from the top of the iPhone.
-
Annulla: non ho completato questa guida.
Altre 154 persone hanno completato questa guida.
4 Commenti
I'll second rafa74's comment: be VERY careful about putting too much stress on the TINY cable that connects the Home button to the rest of its assembly! I ripped mine as well. You have to slowly separate the Home button's plastic sub-assembly from the display module itself (with a kitchen knife, for example). Otherwise the moment you start parting the display module from the mid-board, you run the risk of tearing the Home button cable... it's far too easy.
This guide neglects to point out some very important things at the end of the removal process. For example, that the glass is glued to the phone, or which connectors have to come with the display assembly on the way out.
This is my first opening session and sounds great !!! Thanks I fix it
I swapped motherboard + battery between 2 original iPhone models, but now on one the touchscreen won’t work even if the connector is attached. The flat looks PERFECT, that’s what bothers me the most, the connector looks also greet, same goes for the “slot” on the motherboard. What is going on? I needed to literarily detach the display assembly from the mid frame, tough, to also swap the 2 displays assemblies (long story). Do the touch for some reason won’t work until I put the bezel and all the screws? Thanks