Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Inserisci uno strumento di espulsione della scheda SIM o una graffetta nel foro accanto al jack delle cuffie.
-
Premi sull'attrezzo finché il vassoio della scheda SIM non fuoriesce.
-
-
-
Inserisci uno strumento di apertura per iPod nello spazio tra il coperchio dell'antenna e il frontalino. Il cuneo dello strumento dovrebbe puntare verso la cover dell'antenna. Fai scorrere lo strumento attorno all'angolo e verso l'alto fino a raggiungere il supporto metallico.
-
Ripeti la stessa procedura sull'altro lato del connettore dock.
-
-
-
Rimuovi le tre viti a croce Phillips #00 che fissano il pannello posteriore all'iPhone.
-
-
-
-
Solleva il pannello posteriore tirando lo scovolino in senso orario con un movimento rapido. Applica una forza perpendicolare al piano del gruppo schermo. Potresti aver paura ad andare veloce, ma procedendo lentamente è più facile che la custodia si pieghi.
-
Il pannello posteriore è ancora collegato all'iPhone tramite il cavo del jack delle cuffie, quindi non rimuovere ancora completamente il pannello posteriore dall'iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel up the orange tape securing the white antenna cable to the side of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the two antenna cables from the communications board. Apple used a small dab of glue on these connections, which may make removing the antenna connections harder.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 3 screws:
-
One Phillips #00 screw securing the logic board to the iPhone near the camera.
-
Two Phillips #00 screws, one on either corner of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the camera connector.
-
Lift the camera out of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Working from the edge opposite the battery connectors, insert a spudger between the battery and the plastic frame and pry up on the battery. It is attached to the casing with an adhesive, but should slowly come free.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide a spudger beneath the logic board on the side opposite the battery connector and pry up slightly. Don't lift up too far, because there are still four attached connectors on the bottom of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
In a similar manner, slide a spudger beneath the logic board where the camera was. Again, don't lift up too far yet as there are still four attached connectors on the bottom of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift up the logic board slightly and slide a spudger beneath the logic board to disconnect the display ribbon cable.
-
After freeing the first connector, slide the spudger further towards the battery and the center of the iPhone to disconnect the speaker connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Go to the other side of the logic board and use a spudger to disconnect the touch sensor cable on the under side of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide a spudger beneath the black locking bar and pry up to rotate the bar 90 degrees (the bar is already rotated in the picture).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Hold both the battery and the logic board assembly and slide both parts away from the orange antenna and out of the iPhone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
There are two stacked circuit boards on the iPhone. The communcations board is on the top, and the logic board is located on the bottom.
-
To separate the boards, insert a spudger into the gap in the metal shielding as shown. Carefully pry with the spudger to loosen the connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Continue to separate the two boards. The silver metal shielding may not immediately separate. If necessary, work around the edge of the board to separate the metal shielding.
-
Annulla: non ho completato questa guida.
Altre 32 persone hanno completato questa guida.