Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Attrezzo utilizzato in questo passaggio:Safety Glasses$3.19
-
Se il vetro del display è rotto, l'uso del nastro adesivo sulla superficie impedisce alla rottura di espandersi e previene danni fisici dovuti alle schegge di vetro.
-
Stendi delle strisce sovrapposte di nastro adesivo da pacchi trasparente sul display dell'iPad fino a coprire l'intera superficie. Per rotture molto serie, può essere necessario applicare due strati di nastro sovrapposti.
-
Cerca di seguire al meglio il resto della guida. Tuttavia, una volta che il vetro è crepato, continuerà a rompersi sempre di più mentre procederai alla riparazione. Potresti aver bisogno di strumenti metallici per rimuovere il vetro.
-
-
-
Scalda un iOpener e appoggialo al bordo sinistro per due minuti.
-
-
-
Lascia il plettro infilato nell'iPad leggermente dopo la fotocamera.
-
Prendi un secondo plettro ed infilalo a sinistra della fotocamera, dove sei già passato col primo plettro. Fallo scorrere verso l'angolo in alto a sinistra per tagliare del tutto l'adesivo rimasto.
-
Lascia il secondo plettro sotto l'angolo per evitare che l'adesivo si reincolli raffreddandosi.
-
-
-
-
Rimuovi le quattro viti Phillips da 1,2 mm sopra la staffa del connettore della batteria/schermo.
-
-
-
Usa l'estremità appuntita di uno spudger per scollegare il connettore dei dati dello schermo dal suo alloggiamento sulla scheda logica.
-
Usa l'estremità appuntita di uno spudger per scollegare il connettore del digitalizzatore dal suo alloggiamento sulla scheda logica.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Run the pointed end of a spudger between the looped tape and the plastic cellular antenna housing to make it easier to peel the tape up.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use tweezers to peel up the looped tape adhered over the upper component cable bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following four Phillips screws holding the upper component bracket in place:
-
Two 2.1 mm screws
-
Two 1.2 mm screws
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Press a paper clip or SIM eject tool into the SIM eject hole.
-
Remove the SIM card tray.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the upper antenna interconnect cable from its socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel the upper antenna interconnect cable up off the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to lift the rear-facing camera cable connector from its socket on the logic board.
-
Lift the sensor cable connector from its socket.
-
Disconnect the right cellular antenna from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to disconnect the front-facing camera press connector.
-
Lift the Facetime camera ribbon cable out of the way and disconnect the headphone jack ribbon cable directly underneath it.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the 1.2 mm Phillips screw securing the volume control cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the point of a spudger to lift the volume control cable connector from its socket on the logic board.
-
Be careful to lift up only on the connector itself, not the socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the point of a spudger to disconnect the two lower antenna interconnect cable connectors.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove any tape covering the ZIF connectors near the Lightning connector port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the tip of a spudger to lift each of the two ZIF connector retaining flaps.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull each speaker cable out from its ZIF socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel the lower antenna interconnect cables away from the corner of the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel the left antenna interconnect cable up off the Lightning port cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four 1.5 mm Phillips screws securing the Lightning port to the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Begin to gently lift the Lightning connector cable up.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use an opening pick to separate the adhesive connecting the lightning connector cable to the iPad case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Continue to slide the pick under the Lightning port cable until you reach the end of the logic board.
-
Leave the pick in place to prevent the adhesive from re-adhering.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Bend back the battery connector over the battery, out of the way of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Reheat an iOpener and lay it on the backside of the iPad near the SIM slot for at least two minutes.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Once the adhesive has softened, carefully push the opening pick under the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
Attrezzo utilizzato in questo passaggio:Plastic Cards$2.99-
Once the opening pick has lifted a corner of the logic board, you can insert a plastic card under the board.
-
Slide the plastic card under the logic board, toward the top of the iPad, near the cameras.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a second plastic card underneath the first one.
-
Slide the second plastic card up to the top edge of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift up on the edges of both plastic cards to pry the logic board from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the logic board assembly from the rear case.
-
Annulla: non ho completato questa guida.
Altre 7 persone hanno completato questa guida.
Un commento
This guide needs amending urgently before more people destroy their LCD displays by cutting through the tape holding the backlight to the LCD glass, or pushing a pick or other tool between the LCD glass and touchscreen glass.
The guide states:
Don't insert the opening pick any deeper than the black bezel on the side of the display.
This is WRONG and will destroy your display. The black bezel is 5mm wide, this is beyond the 1mm wide adhesive and into the LCD display and backlight assembly. Do not insert anything more than 2mm down the sides of the display.
Any further than 2mm and, like me, you will be looking at a very expensive LCD display replacement.
Thanks IFIXIT.COM for publishing an incorrect guide that has destroyed my display.