Salta al contenuto principale
  1. Ti raccomandiamo di pulire il tuo forno a microonde prima dell'operazione, perché ignobili entità unte e appiccicose potrebbero attaccarsi all'iOpener. Disponi l'iOpener al centro del tuo forno a microonde.
    • Ti raccomandiamo di pulire il tuo forno a microonde prima dell'operazione, perché ignobili entità unte e appiccicose potrebbero attaccarsi all'iOpener.

    • Disponi l'iOpener al centro del tuo forno a microonde.

    • Per forni a microonde con piatto rotante: assicurati che il piatto giri liberamente. Se l'iOpener si incastrasse da qualche parte, potrebbe surriscaldarsi e bruciare.

  2. Riscalda l'iOpener per 30 secondi.
    • Riscalda l'iOpener per 30 secondi.

    • Se durante la riparazione l'iOpener si raffredda, scaldalo di nuovo nel microonde per 30 secondi.

    • Fai attenzione a non surriscaldare l'iOpener durante l'operazione. Il surriscaldamento può far bruciare l'iOpener.

    • Non toccare mai l'iOpener se appare gonfio.

    • Se l'iOpener è ancora troppo caldo in mezzo per poterlo toccare, continua a utilizzarlo mentre attendi che si raffreddi un po' prima di scaldarlo di nuovo. Un iOpener riscaldato correttamente dovrebbe rimanere caldo fino a 10 minuti.

  3. Rimuovi l'iOpener dal forno a microonde, afferrandolo per una delle due estremità piatte per evitare il contatto con la parte centrale calda.
    • Rimuovi l'iOpener dal forno a microonde, afferrandolo per una delle due estremità piatte per evitare il contatto con la parte centrale calda.

    • L'iOpener sarà davvero caldissimo, perciò fai attenzione quando lo maneggi. Usa una presina da forno, se necessario.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass. Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered. This will keep glass shards contained and provide structural integrity when prying and lifting the display.
    • If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.

    • Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.

    • This will keep glass shards contained and provide structural integrity when prying and lifting the display.

    • Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.

    • Wear safety glasses to protect your eyes, and be careful not to damage the LCD screen.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Handling it by the tab, place the heated iOpener on the side of the iPad to the left of the home button assembly.
    • Handling it by the tab, place the heated iOpener on the side of the iPad to the left of the home button assembly.

    • Let the iOpener sit for about five minutes to soften the adhesive beneath the glass.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Carefully place a suction cup halfway up the heated side. Be sure the cup is completely flat on the screen to get a tight seal. While holding the iPad down with one hand, pull up on the suction cup to slightly separate the front panel glass from from the rear case.
    • Carefully place a suction cup halfway up the heated side.

    • Be sure the cup is completely flat on the screen to get a tight seal.

    • While holding the iPad down with one hand, pull up on the suction cup to slightly separate the front panel glass from from the rear case.

    • Be careful to only lift the glass enough to insert an opening pick—any more and you risk cracking the glass.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    While holding the glass up with the suction cup, slide the point of an opening pick into the gap between the glass and body of the iPad. Don't insert the opening pick any deeper than the black bezel on the side of the display. Inserting the pick too far may damage the LCD. Pull the suction cup's plastic nub to release the vacuum seal and remove the suction cup from the display assembly.
    • While holding the glass up with the suction cup, slide the point of an opening pick into the gap between the glass and body of the iPad.

    • Don't insert the opening pick any deeper than the black bezel on the side of the display. Inserting the pick too far may damage the LCD.

    • Pull the suction cup's plastic nub to release the vacuum seal and remove the suction cup from the display assembly.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Reheat and reapply the iOpener.
    • Reheat and reapply the iOpener.

    • Be careful not to overheat the iOpener during the repair procedure. Always wait at least ten minutes before reheating the iOpener.

    • Let it rest for a few minutes to reheat the left edge of the iPad.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Place a second opening pick alongside the first and slide the pick down along the edge of the iPad, releasing the adhesive as you go. Throughout the rest of the procedure, if you encounter significant resistance to sliding picks beneath the glass, stop and reheat the section you're working on. Forcing the picks risks cracking the glass. Throughout the rest of the procedure, if you encounter significant resistance to sliding picks beneath the glass, stop and reheat the section you're working on. Forcing the picks risks cracking the glass.
    • Place a second opening pick alongside the first and slide the pick down along the edge of the iPad, releasing the adhesive as you go.

    • Throughout the rest of the procedure, if you encounter significant resistance to sliding picks beneath the glass, stop and reheat the section you're working on. Forcing the picks risks cracking the glass.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Continue moving the opening pick down the side of the display to release the adhesive. If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive. If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive.
    • Continue moving the opening pick down the side of the display to release the adhesive.

    • If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Take the first pick you inserted and slide it up toward the top corner of the iPad. If you can see the tip of the opening pick through the front glass, don't panic—just pull the pick out a little bit. Most likely, everything will be fine, but try to avoid this as it may deposit adhesive on the front of the LCD that is difficult to clean off. If you can see the tip of the opening pick through the front glass, don't panic—just pull the pick out a little bit. Most likely, everything will be fine, but try to avoid this as it may deposit adhesive on the front of the LCD that is difficult to clean off.
    • Take the first pick you inserted and slide it up toward the top corner of the iPad.

    • If you can see the tip of the opening pick through the front glass, don't panic—just pull the pick out a little bit. Most likely, everything will be fine, but try to avoid this as it may deposit adhesive on the front of the LCD that is difficult to clean off.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Reheat the iOpener and place it on the top edge of the iPad, over the front-facing camera.
    • Reheat the iOpener and place it on the top edge of the iPad, over the front-facing camera.

    • Be careful not to overheat the iOpener during the repair procedure. Wait at least ten minutes before reheating the iOpener.

    • If you have a flexible iOpener, you can bend it to heat both the upper left corner and the upper edge at the same time.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Slide the opening pick around the top left corner of the iPad to separate the adhesive. Slide the opening pick around the top left corner of the iPad to separate the adhesive. Slide the opening pick around the top left corner of the iPad to separate the adhesive.
    • Slide the opening pick around the top left corner of the iPad to separate the adhesive.

  14. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Slide the opening pick along the top edge of the iPad, stopping just before you reach the camera. The third image shows where the front-facing camera and housing are in the iPad. Avoid sliding the opening pick over the front-facing camera, as you may smear adhesive onto the lens or damage the camera. The following steps will detail how to best avoid disturbing the front-facing camera.
    • Slide the opening pick along the top edge of the iPad, stopping just before you reach the camera.

    • The third image shows where the front-facing camera and housing are in the iPad.

    • Avoid sliding the opening pick over the front-facing camera, as you may smear adhesive onto the lens or damage the camera. The following steps will detail how to best avoid disturbing the front-facing camera.

  15. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Pull the pick out slightly, and slide the very tip gently along the top of the front-facing camera section of the top edge. Pull the pick out slightly, and slide the very tip gently along the top of the front-facing camera section of the top edge. Pull the pick out slightly, and slide the very tip gently along the top of the front-facing camera section of the top edge.
    • Pull the pick out slightly, and slide the very tip gently along the top of the front-facing camera section of the top edge.

  16. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Leave the opening pick in the iPad slightly past the front-facing camera. Take a second pick and insert it to the left of the camera, where the first pick just was. Slide it back to the corner to completely cut any remaining adhesive. Leave the second pick in place to prevent the corner adhesive from re-sealing as it cools.
    • Leave the opening pick in the iPad slightly past the front-facing camera.

    • Take a second pick and insert it to the left of the camera, where the first pick just was. Slide it back to the corner to completely cut any remaining adhesive.

    • Leave the second pick in place to prevent the corner adhesive from re-sealing as it cools.

  17. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Insert the previous pick deeper into the iPad and slide it away from the camera toward the corner. Be very careful of the small antenna cable near the upper-right corner. Only slide the pick away from the camera—while sliding it in the opposite direction you may accidentally tear the antenna cable. Be very careful of the small antenna cable near the upper-right corner. Only slide the pick away from the camera—while sliding it in the opposite direction you may accidentally tear the antenna cable.
    • Insert the previous pick deeper into the iPad and slide it away from the camera toward the corner.

    • Be very careful of the small antenna cable near the upper-right corner. Only slide the pick away from the camera—while sliding it in the opposite direction you may accidentally tear the antenna cable.

  18. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Leave the three picks in the corners of the iPad to prevent re-adhering of the front panel adhesive.
    • Leave the three picks in the corners of the iPad to prevent re-adhering of the front panel adhesive.

    • Reheat the iOpener and place it on the remaining long side of the iPad—along the volume and lock buttons.

  19. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Slide the top right opening pick around the corner to fully release the top edge of the glass. Leave this pick in place to keep the adhesive from re-sealing itself, and grab a new pick for the next step.
    • Slide the top right opening pick around the corner to fully release the top edge of the glass.

    • Leave this pick in place to keep the adhesive from re-sealing itself, and grab a new pick for the next step.

  20. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Insert a new opening pick and slide it to the middle of the right edge of the iPad, releasing the adhesive as you go. Insert a new opening pick and slide it to the middle of the right edge of the iPad, releasing the adhesive as you go. Insert a new opening pick and slide it to the middle of the right edge of the iPad, releasing the adhesive as you go.
    • Insert a new opening pick and slide it to the middle of the right edge of the iPad, releasing the adhesive as you go.

  21. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Continue to slide the pick down the right edge of the iPad, releasing the adhesive. Continue to slide the pick down the right edge of the iPad, releasing the adhesive. Continue to slide the pick down the right edge of the iPad, releasing the adhesive.
    • Continue to slide the pick down the right edge of the iPad, releasing the adhesive.

  22. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Leave the opening picks in place and reheat the iOpener.
    • Leave the opening picks in place and reheat the iOpener.

    • Remember not to overheat the iOpener—no more than once every ten minutes.

    • Set the reheated iOpener on the home button end of the iPad and let it rest for a few minutes to soften the adhesive beneath the glass.

  23. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Slide the lower left pick to the lower left corner to cut the adhesive on that corner. Leave the pick at the corner. Do not pry any farther, and do not remove the pick from the iPad. There are quite a few things to avoid beneath the lower bezel, so study the third image closely:
    • Slide the lower left pick to the lower left corner to cut the adhesive on that corner.

    • Leave the pick at the corner. Do not pry any farther, and do not remove the pick from the iPad.

    • There are quite a few things to avoid beneath the lower bezel, so study the third image closely:

    • Antennas

    • Home button cavity

    • Digitizer cable

    • The following steps will direct you where to pry to avoid damage to these components. Only apply heat and pry where directed.

  24. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Leave the pick from the last step in place to prevent the adhesive from re-sealing. With a new pick, slice gently over the left-hand antenna, stopping before the home button. Only slide the pick from the outer edge toward the center of the iPad. Do not move the pick back toward the outer edge, as moving in this direction may damage the antenna.
    • Leave the pick from the last step in place to prevent the adhesive from re-sealing.

    • With a new pick, slice gently over the left-hand antenna, stopping before the home button.

    • Only slide the pick from the outer edge toward the center of the iPad. Do not move the pick back toward the outer edge, as moving in this direction may damage the antenna.

    • If you need to slide the pick over the lower section more than once, remove it and re-insert at the outer edge, and slide inwards.

    • Leave the pick in place before moving on.

  25. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Insert the tip of one last pick next to the previous step's pick, and slide it beneath the home button. Stop about an inch from the right-hand side to avoid cutting the digitizer cable. Insert the pick slightly deeper and work it back toward the home button.
    • Insert the tip of one last pick next to the previous step's pick, and slide it beneath the home button.

    • Stop about an inch from the right-hand side to avoid cutting the digitizer cable.

    • Insert the pick slightly deeper and work it back toward the home button.

    • Again, be sure to only slide the pick toward the center of the iPad when it is fully inserted; otherwise you may damage the antenna beneath the glass.

  26. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Reheat and reapply the iOpener to the top bezel of the iPad.
    • Reheat and reapply the iOpener to the top bezel of the iPad.

  27. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Be very careful with this step. Take your time and ensure the adhesive is hot and soft, and that you've been through all of the adhesive with an opening pick. Don't be afraid to stop and reheat. At the top of the iPad opposite the home button, you should have a pick lodged into each corner. Twist the picks to lift the glass slightly, separating the last of the adhesive along all four edges.
    • Be very careful with this step. Take your time and ensure the adhesive is hot and soft, and that you've been through all of the adhesive with an opening pick. Don't be afraid to stop and reheat.

    • At the top of the iPad opposite the home button, you should have a pick lodged into each corner. Twist the picks to lift the glass slightly, separating the last of the adhesive along all four edges.

    • If you encounter a significant amount of resistance, stop twisting. Leave the picks in place, reheat, and reapply the iOpener to the problem areas, and run a pick through the sticking point one more time.

  28. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Lift slowly and gently to further detach the adhesive along the lower edge. Lift slowly and gently to further detach the adhesive along the lower edge.
    • Lift slowly and gently to further detach the adhesive along the lower edge.

  29. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Once all of the adhesive has been separated, open the front glass like a page in a book and rest it on your workspace. If you plan to reuse the front panel assembly, you will need to replace the display adhesive. Use our display adhesive application guide to reapply your display adhesive and reseal your device.
    • Once all of the adhesive has been separated, open the front glass like a page in a book and rest it on your workspace.

    • If you plan to reuse the front panel assembly, you will need to replace the display adhesive. Use our display adhesive application guide to reapply your display adhesive and reseal your device.

  30. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    The front-facing camera housing may stick to the front panel; peel up the housing and place it back over the camera to protect it. Rock the camera housing up on one edge to free it from the adhesive and remove it from the front panel. Return the front-facing camera housing to its recess in the rear case.
    • The front-facing camera housing may stick to the front panel; peel up the housing and place it back over the camera to protect it.

    • Rock the camera housing up on one edge to free it from the adhesive and remove it from the front panel.

    • Return the front-facing camera housing to its recess in the rear case.

  31. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the following Phillips #00 screws securing the LCD: Three 3.3 mm screws
    • Remove the following Phillips #00 screws securing the LCD:

    • Three 3.3 mm screws

    • One 4.5 mm screw

    • If there is tape covering any LCD screws, peel it up with tweezers.

  32. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Do not attempt to fully remove the LCD. It is still connected to the iPad by several cables at the home button end. Lift only from the front-facing camera end. Insert the flat end of a spudger under the LCD between it and the LCD shield plate and lift gently.
    • Do not attempt to fully remove the LCD. It is still connected to the iPad by several cables at the home button end. Lift only from the front-facing camera end.

    • Insert the flat end of a spudger under the LCD between it and the LCD shield plate and lift gently.

    • Be very careful not to get the spudger under the shield plate. It must be between the LCD and the shield.

    • Even bending the LCD slightly can permanently damage it, so be extremely careful as you lift.

  33. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    The LCD is secured by mild adhesive that should be loosened before you flip the LCD up from its shield plate. Insert the spudger between the LCD and LCD shield plate and slide it to the far edge of the iPad. Insert the spudger between the LCD and LCD shield plate and slide it to the far edge of the iPad.
    • The LCD is secured by mild adhesive that should be loosened before you flip the LCD up from its shield plate.

    • Insert the spudger between the LCD and LCD shield plate and slide it to the far edge of the iPad.

  34. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Two wide strips of tape connect the LCD to the speakers. Hold the LCD with one hand, and the rear body of the iPad with the other.
    • Two wide strips of tape connect the LCD to the speakers.

    • Hold the LCD with one hand, and the rear body of the iPad with the other.

    • Do not attempt to fully remove the LCD from the iPad.

    • Gently pull the LCD away from the speakers to separate the tape, being careful not to pull on the digitizer cable.

  35. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Do not attempt to fully remove the LCD. It is still connected to the iPad by several cables at the home button end. Lift only from the front-facing camera end. Flip the iPad LCD like a page in a book, lifting near the camera and turning it over the home button end of the rear case.
    • Do not attempt to fully remove the LCD. It is still connected to the iPad by several cables at the home button end. Lift only from the front-facing camera end.

    • Flip the iPad LCD like a page in a book, lifting near the camera and turning it over the home button end of the rear case.

    • Be gentle and keep an eye on the LCD cables as you flip the display over.

    • Lay the LCD on the front panel glass to allow access to the display cables.

  36. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Slide the tip of a spudger between the LCD and the adhesive tabs to free the display. Push gently between each of the two adhesive tabs; be careful not to damage any of the nearby cables. Push gently between each of the two adhesive tabs; be careful not to damage any of the nearby cables.
    • Slide the tip of a spudger between the LCD and the adhesive tabs to free the display.

    • Push gently between each of the two adhesive tabs; be careful not to damage any of the nearby cables.

  37. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the seven 1.8 mm Phillips #00 screws from the LCD shield plate.
    • Remove the seven 1.8 mm Phillips #00 screws from the LCD shield plate.

  38. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the flat end of a spudger to pry the LCD shield plate up and out of the iPad. Remove the LCD shield plate. Remove the LCD shield plate.
    • Use the flat end of a spudger to pry the LCD shield plate up and out of the iPad.

    • Remove the LCD shield plate.

  39. Svita le seguenti viti a croce Phillips #00 dalla copertura dei cavi dello schermo:
    • Svita le seguenti viti a croce Phillips #00 dalla copertura dei cavi dello schermo:

    • Una vite da 2,8 mm

    • Tre viti da 1,4 mm

  40. Rimuovi la copertura dei cavi dello schermo dall'iPad. Rimuovi la copertura dei cavi dello schermo dall'iPad. Rimuovi la copertura dei cavi dello schermo dall'iPad.
    • Rimuovi la copertura dei cavi dello schermo dall'iPad.

  41. Usa la punta di uno spudger per sollevare il connettore del tasto Home dalla sua presa sulla scheda madre. Piega il cavo a nastro del tasto Home per disporlo in modo che non intralci il lavoro. Piega il cavo a nastro del tasto Home per disporlo in modo che non intralci il lavoro.
    • Usa la punta di uno spudger per sollevare il connettore del tasto Home dalla sua presa sulla scheda madre.

    • Piega il cavo a nastro del tasto Home per disporlo in modo che non intralci il lavoro.

  42. Usa la punta di uno spudger per sollevare delicatamente il connettore della batteria dalla sua presa sulla scheda madre. Stai attento a fare leva solo sul connettore della batteria e non sulla presa. Se fai leva sulla presa sulla scheda madre, potresti romperla irreparabilmente. Stai attento a fare leva solo sul connettore della batteria e non sulla presa. Se fai leva sulla presa sulla scheda madre, potresti romperla irreparabilmente.
    • Usa la punta di uno spudger per sollevare delicatamente il connettore della batteria dalla sua presa sulla scheda madre.

    • Stai attento a fare leva solo sul connettore della batteria e non sulla presa. Se fai leva sulla presa sulla scheda madre, potresti romperla irreparabilmente.

  43. Usa la punta di uno spudger per sollevare il connettore del pannello LCD dalla sua presa sulla scheda madre. Non fare leva contro il grosso chip accanto al connettore o potresti romperlo. Fai leva delicatamente sul lato del connettore come mostrato nelle immagini.
    • Usa la punta di uno spudger per sollevare il connettore del pannello LCD dalla sua presa sulla scheda madre.

    • Non fare leva contro il grosso chip accanto al connettore o potresti romperlo. Fai leva delicatamente sul lato del connettore come mostrato nelle immagini.

  44. Solleva e rimuovi il pannello LCD dall'iPad Mini 3.
    • Solleva e rimuovi il pannello LCD dall'iPad Mini 3.

  45. Usa la punta di uno spudger per sollevare il connettore del cavo del digitizer dalla sua presa. Usa la punta di uno spudger per sollevare il connettore del cavo del digitizer dalla sua presa.
    • Usa la punta di uno spudger per sollevare il connettore del cavo del digitizer dalla sua presa.

  46. Fai scorrere la parte piatta di uno spudger sotto il bordo vicino alla batteria della scheda del digitizer per iniziare a rimuovere la cella dalla scocca. Fai scorrere la parte piatta di uno spudger sotto il bordo vicino alla batteria della scheda del digitizer per iniziare a rimuovere la cella dalla scocca.
    • Fai scorrere la parte piatta di uno spudger sotto il bordo vicino alla batteria della scheda del digitizer per iniziare a rimuovere la cella dalla scocca.

  47. Solleva la scheda del digitizer per separarla dall'adesivo. Solleva la scheda del digitizer per separarla dall'adesivo.
    • Solleva la scheda del digitizer per separarla dall'adesivo.

  48. Solleva e rimuovi il gruppo del pannello forntale dall'iPad.
    • Solleva e rimuovi il gruppo del pannello forntale dall'iPad.

  49. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the tip of a spudger to peel the tape off of the antenna cables near the logic board. Use the tip of a spudger to peel the tape off of the antenna cables near the logic board.
    • Use the tip of a spudger to peel the tape off of the antenna cables near the logic board.

  50. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the point of a spudger to separate the adhesive holding the antennas to the right speaker. Use the point of a spudger to separate the adhesive holding the antennas to the right speaker.
    • Use the point of a spudger to separate the adhesive holding the antennas to the right speaker.

  51. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the point of a spudger to lift the antenna cable adhesive up off the rear case. Use the point of a spudger to lift the antenna cable adhesive up off the rear case.
    • Use the point of a spudger to lift the antenna cable adhesive up off the rear case.

  52. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the following Phillips #00 screws from the left antenna:
    • Remove the following Phillips #00 screws from the left antenna:

    • One 2.6 mm screw

    • Two 1.5 mm screws

  53. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the flat end of a spudger to loosen the foam adhesive securing the Wi-Fi antenna to the left speaker. Use the flat end of a spudger to loosen the foam adhesive securing the Wi-Fi antenna to the left speaker.
    • Use the flat end of a spudger to loosen the foam adhesive securing the Wi-Fi antenna to the left speaker.

  54. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the flat end of a spudger to fold the wide left-hand piece of tape away from the left speaker. Use the flat end of a spudger to fold the wide left-hand piece of tape away from the left speaker.
    • Use the flat end of a spudger to fold the wide left-hand piece of tape away from the left speaker.

  55. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the tip of a spudger to pry the antenna cable tape up from the rear case of the iPad. Gently pull the antenna cable out of the way as you work along the piece of tape to free it and keep it from resealing. Gently pull the antenna cable out of the way as you work along the piece of tape to free it and keep it from resealing.
    • Use the tip of a spudger to pry the antenna cable tape up from the rear case of the iPad.

    • Gently pull the antenna cable out of the way as you work along the piece of tape to free it and keep it from resealing.

  56. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Pull the antenna cable from the clip behind the Lightning connector. Pull the antenna cable from the clip behind the Lightning connector.
    • Pull the antenna cable from the clip behind the Lightning connector.

  57. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Pull the wide tape toward the battery, applying constant force to peel it from the antenna cable lodged between it and the speaker. Insert a plastic opening tool into the gap between the wide tape and the antenna cable, to break the adhesive connecting the two. Slide the plastic opening tool along the length of the antenna cable to completely separate it from the piece of tape.
    • Pull the wide tape toward the battery, applying constant force to peel it from the antenna cable lodged between it and the speaker.

    • Insert a plastic opening tool into the gap between the wide tape and the antenna cable, to break the adhesive connecting the two.

    • Slide the plastic opening tool along the length of the antenna cable to completely separate it from the piece of tape.

  58. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Lift the antenna cable tape up from behind the right speaker. Lift the antenna cable tape up from behind the right speaker. Lift the antenna cable tape up from behind the right speaker.
    • Lift the antenna cable tape up from behind the right speaker.

  59. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Pull the antenna cable out from under the corner of the right speaker. Pull the antenna cable out from under the corner of the right speaker.
    • Pull the antenna cable out from under the corner of the right speaker.

  60. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the point of a spudger to pull the antenna cable clip toward the battery to allow access to the cables. Use the point of a spudger to pull the antenna cable clip toward the battery to allow access to the cables.
    • Use the point of a spudger to pull the antenna cable clip toward the battery to allow access to the cables.

  61. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    De-route the antenna cable from the retaining clip. De-route the antenna cable from the retaining clip.
    • De-route the antenna cable from the retaining clip.

  62. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the point of a spudger to lift the left antenna cable connector straight up off of its socket on the logic board. Use the point of a spudger to lift the left antenna cable connector straight up off of its socket on the logic board.
    • Use the point of a spudger to lift the left antenna cable connector straight up off of its socket on the logic board.

  63. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the left antenna from the iPad.
    • Remove the left antenna from the iPad.

Linea Traguardo

Sam Goldheart

Membro da: 18/10/2012

437.980 Reputazione

547 Guide realizzate

Team

iFixit Membro di iFixit

Community

137 Membri

16.057 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 4

Tutti i Tempi: 637