Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Riempi una pentola o una padella con abbastanza acqua per immergerci un iOpener.
-
Scalda l'acqua finché non bolle. Spegni il fuoco.
-
Posiziona l'iOpener nell'acqua calda per 2-3 minuti. Assicurati che l'iOpener sia completamente immerso nell'acqua.
-
Usa delle pinze per estrarre l'iOpener scaldato dall'acqua calda.
-
Asciuga accuratamente l'iOpener con un asciugamano.
-
Il tuo iOpener è pronto all'uso! Se devi scaldare di nuovo l'iOpener, scalda l'acqua fino all'ebollizione, spegni il fuoco e immergi l'iOpener in acqua per 2-3 minuti.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
-
Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.
-
Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Handling it by the tab, place the heated iOpener on the side of the iPad to the left of the home button assembly.
-
Let the iOpener sit for about five minutes to soften the adhesive beneath the glass.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully place a suction cup halfway up the heated side.
-
Be sure the cup is completely flat on the screen to get a tight seal.
-
While holding the iPad down with one hand, pull up on the suction cup to slightly separate the front panel glass from from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
While holding the glass up with the suction cup, slide the point of an opening pick into the gap between the glass and body of the iPad.
-
Pull the suction cup's plastic nub to release the vacuum seal and remove the suction cup from the display assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Reheat and reapply the iOpener.
-
Let it rest for a few minutes to reheat the left edge of the iPad.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Place a second opening pick alongside the first and slide the pick down along the edge of the iPad, releasing the adhesive as you go.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Continue moving the opening pick down the side of the display to release the adhesive.
-
If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Take the first pick you inserted and slide it up toward the top corner of the iPad.
-
If you can see the tip of the opening pick through the front glass, don't panic—just pull the pick out a little bit. Most likely, everything will be fine, but try to avoid this as it may deposit adhesive on the front of the LCD that is difficult to clean off.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Reheat the iOpener and place it on the top edge of the iPad, over the front-facing camera.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the opening pick around the top left corner of the iPad to separate the adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the opening pick along the top edge of the iPad, stopping just before you reach the camera.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the pick out slightly, and slide the very tip gently along the top of the front-facing camera section of the top edge.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Leave the opening pick in the iPad slightly past the front-facing camera.
-
Take a second pick and insert it to the left of the camera, where the first pick just was. Slide it back to the corner to completely cut any remaining adhesive.
-
Leave the second pick in place to prevent the corner adhesive from re-sealing as it cools.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the previous pick deeper into the iPad and slide it away from the camera toward the corner.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Leave the three picks in the corners of the iPad to prevent re-adhering of the front panel adhesive.
-
Reheat the iOpener and place it on the remaining long side of the iPad—along the volume and lock buttons.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the top right opening pick around the corner to fully release the top edge of the glass.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a new opening pick and slide it to the middle of the right edge of the iPad, releasing the adhesive as you go.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Continue to slide the pick down the right edge of the iPad, releasing the adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Leave the opening picks in place and reheat the iOpener.
-
Set the reheated iOpener on the home button end of the iPad and let it rest for a few minutes to soften the adhesive beneath the glass.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the lower left pick to the lower left corner to cut the adhesive on that corner.
-
Leave the pick at the corner. Do not pry any farther, and do not remove the pick from the iPad.
-
Antennas
-
Home button cavity
-
Digitizer cable
-
The following steps will direct you where to pry to avoid damage to these components. Only apply heat and pry where directed.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
With a new pick, slice gently over the left-hand antenna, stopping before the home button.
-
Leave the pick in place before moving on.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the tip of one last pick next to the previous step's pick, and slide it beneath the home button.
-
Insert the pick slightly deeper and work it back toward the home button.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Reheat and reapply the iOpener to the top bezel of the iPad.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
At the top of the iPad opposite the home button, you should have a pick lodged into each corner. Twist the picks to lift the glass slightly, separating the last of the adhesive along all four edges.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift slowly and gently to further detach the adhesive along the lower edge.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Once all of the adhesive has been separated, open the front glass like a page in a book and rest it on your workspace.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rock the camera housing up on one edge to free it from the adhesive and remove it from the front panel.
-
Return the front-facing camera housing to its recess in the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following Phillips #00 screws securing the LCD:
-
Three 3.3 mm screws
-
One 4.5 mm screw
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the flat end of a spudger under the LCD between it and the LCD shield plate and lift gently.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the spudger between the LCD and LCD shield plate and slide it to the far edge of the iPad.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Hold the LCD with one hand, and the rear body of the iPad with the other.
-
Gently pull the LCD away from the speakers to separate the tape, being careful not to pull on the digitizer cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip the iPad LCD like a page in a book, lifting near the camera and turning it over the home button end of the rear case.
-
Lay the LCD on the front panel glass to allow access to the display cables.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the tip of a spudger between the LCD and the adhesive tabs to free the display.
-
Push gently between each of the two adhesive tabs; be careful not to damage any of the nearby cables.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the seven 1.8 mm Phillips #00 screws from the LCD shield plate.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry the LCD shield plate up and out of the iPad.
-
Remove the LCD shield plate.
-
-
-
Svita le seguenti viti a croce Phillips #00 dalla copertura dei cavi dello schermo:
-
Una vite da 2,8 mm
-
Tre viti da 1,4 mm
-
-
-
Usa la punta di uno spudger per sollevare il connettore del cavo del digitizer dalla sua presa.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use an opening pick to break up the adhesive holding the home button ribbon cable to the digitizer cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert an opening pick between the home button ribbon cable and the digitizer.
-
Slide the pick along the front panel, towards the home button, to continue separating the home button ribbon cable from the front panel.
-
-
-
Prepara un iOpener e appoggialo sul lato inferiore del digitizer per ammorbidire l'adesivo che tiene ferme le guarnizioni del pulsante Home.
-
Gira sottosopra il pannello del digitizer e spingi delicatamente il pulsante Home verso l'alto per estrarlo dalla sua locazione sul pannello frontale.
-
-
-
Piega il cavo del digitizer su se stesso e premilo con decisione per incollarlo all'adesivo.
-
-
-
Rimuovi le coperture in plastica dell'adesivo attorno al perimetro del gruppo del pannello anteriore.
-
Rimuovi il piccolo pezzo di adesivo protettivo dal cavo del digitizer.
-
Assicurati che tutto il rame sia coperto sul nuovo schermo di ricambio, altrimenti, una volta installato in questo modo, potrebbe muoversi in modo casuale.
-
-
-
Appoggia la punta di uno strumento di apertura in plastica su ogni lato del magnete vicino all'angolo in alto a sinistra del gruppo del pannello anteriore.
-
Infila attentamente la punta dello strumento di apertura in plastica di destra sotto il magnete.
-
Infila la punta dello strumento di apertura in plastica di sinistra sotto il magnete mentre fai leva e lo spingi verso lo strumento di destra.
-
Annulla: non ho completato questa guida.
Altre 19 persone hanno completato questa guida.
6 Commenti
This is NOT the iPad Mini 3 LTE… please fix the guide so people won't break the LCD when they follow these instructions.
Remember, fixit get money from us buying parts. so the more we try or break, the more parts we might need. so they only will give us enough info for us to be brave to try to repair. that is why before I do any repairs that I haven tried in the past, I will check here and also you tube videos from other people who tried and compare notes or tips where I have to be careful.
Showing the wrong model iPad in the tutorial cost me a $55 mistake.