Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Riempi una pentola o una padella con abbastanza acqua per immergerci un iOpener.
-
Scalda l'acqua finché non bolle. Spegni il fuoco.
-
Posiziona l'iOpener nell'acqua calda per 2-3 minuti. Assicurati che l'iOpener sia completamente immerso nell'acqua.
-
Usa delle pinze per estrarre l'iOpener scaldato dall'acqua calda.
-
Asciuga accuratamente l'iOpener con un asciugamano.
-
Il tuo iOpener è pronto all'uso! Se devi scaldare di nuovo l'iOpener, scalda l'acqua fino all'ebollizione, spegni il fuoco e immergi l'iOpener in acqua per 2-3 minuti.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a SIM eject tool or an uncoiled paperclip to eject the SIM tray.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the SIM tray out of its slot and remove it from the iPad.
-
-
-
Se il vetro dello schermo è crepato, previeni ulteriori rotture e danni fisici durante la riparazione coprendo lo schermo con del nastro adesivo trasparente.
-
Sovrapponi strisce di nastro adesivo trasparente per coprire tutta la superficie dello schermo dell´iPad.
-
Fai del tuo meglio per seguire il resto della guida, come descritta. In ogni caso, uno schermo crepato continuerà probabilmente a danneggiarsi durante la riparazione e, perciò potrebbe essere necessario utilizzare uno strumento metallico per estrarre il vetro.
-
-
-
C'è una piccola fessura nell'anello adesivo dell'iPad nell'angolo in alto a destra, a circa 5 cm dal bordo superiore. Dovrai sfruttare questa debolezza.
-
Allinea lo strumento con il tasto del muto. Infila la punta di uno uno strumento di apertura in plastica nella fessura tra il vetro anteriore e il bordo in plastica. Infila solo la punta dello strumento, solo abbastanza per allargarla.
-
-
-
Una volta superata l'antenna WiFi (a circa da 75 mm dal bordo destro, o accanto al tasto Home), reinfila il plettro completamente.
-
Fai scorrere il plettro verso destra, rilasciando l'adesivo che fissa l'antenna WiFi al vetro anteriore.
-
L'antenna del WiFi è attaccata al bordo inferiore dell'iPad tramite delle viti e un cavo. Questo passaggio separa l'antenna dal pannello anteriore, assicurando che quando lo rimuoverai l'antenna non verrà danneggiata.
-
-
-
-
Fai scorrere il plettro sotto il bordo superiore dell'iPad, sfilandolo leggermente per aggirare la staffa della fotocamera anteriore.
-
L'adesivo in questa zona è molto spesso e può essere richiesta abbastanza forza. Lavora attentamente e lentamente, assicurandoti di non scivolare e danneggiare te stesso o l'iPad.
-
-
-
Svita le quattro viti a croce Phillips #00 da 2 mm che fissano il pannello LCD alla cornice in alluminio.
-
-
-
Usando la punta di uno spudger, rimuovi il pezzo di nastro che copre il connettore del cavo a nastro del pannello LCD.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel back and remove the piece of electrical tape covering the headphone jack assembly cable connector.
-
Using the tip of a spudger, flip up the retaining flap on both of the ZIF connectors securing the headphone jack cable to the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the flat end of a spudger underneath the headphone jack assembly cable, releasing the adhesive securing it to the rear aluminum frame.
-
Pull the headphone jack assembly cable straight out of its socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel back and remove the piece of tape covering the SIM board cable ZIF connector.
-
Flip up the retaining flap on the SIM board cable ZIF connector.
-
Using the tip of a spudger, pull the SIM board cable straight out of its socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three 1.75 mm Phillips #00 screws securing the SIM board to the aluminum frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Holding the headphone jack assembly cable out of the way, remove the SIM board from the iPad.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel back and remove the adhesive tape covering the headphone jack assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 2.6 mm Phillips #0 screw securing the camera cable to the headphone jack assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the flat end of a spudger, pry the front-facing camera off of its socket on the headphone jack assembly.
-
Without removing the spudger, slide the spudger to the right, releasing the adhesive holding down the camera cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tip of the spudger, flip up the retaining flap on the microphone cable ZIF connector.
-
Insert the tip of the spudger underneath the microphone ribbon cable, removing it from its ZIF connector.
-
Slide the spudger to the left, releasing the adhesive holding the microphone ribbon cable to the headphone jack assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of the spudger to pry up the antenna connector cable out of its socket on the headphone jack assembly board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip up the retaining flap securing the volume/power button ribbon cable connector to the headphone jack assembly board.
-
Remove the volume button ribbon cable from its ZIF connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following screws from the headphone jack assembly:
-
Five 2.6 mm Phillips #0
-
Two 2.2 mm Wide Head Phillips #00
-
Two 2.6 mm Phillips #00
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Holding onto the ribbon cable of the headphone jack assembly, carefully pull the assembly parallel to the iPad, toward the bottom of the device.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasping the headphone jack assembly with both hands, pull the assembly from the iPad, minding any cables that may get caught.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following screws securing the power & volume button cable to the aluminum frame:
-
Two 5.5 mm Phillips #0
-
One 2.6 mm Phillips #0
-
Two 2.6 mm Phillips #0
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the piece of plastic covering the volume buttons.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 2.6 mm Phillips #00 screw holding the volume button frame to the aluminum frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Wedge the edge of a plastic opening tool underneath the sleep/wake sensor, being careful to not damage the fragile cable.
-
Move the plastic opening tool around the sensor, releasing the adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide a spudger underneath the power & volume cables, releasing the adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tip of the spudger rather that the wide edge, release the adhesive underneath the volume button branch of the ribbon cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Continue sliding the tip of the spudger toward the top of the iPad, releasing the adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
With the tip of the spudger still underneath the ribbon cable, gently lift the power button out of its socket in the aluminum frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Holding the power & volume button cable with with both hands, carefully pull the volume buttons and lock switch from their sockets in the aluminum frame.
-
Lift and remove the power & volume button cable out of the rear aluminum case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the spudger to help guide it out of the iPad, push the mute/lock switch out of its recess in the aluminum frame.
-
Lift and remove the mute/lock switch out of the rear aluminum case.
-