Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Riempi una pentola o una padella con abbastanza acqua per immergerci un iOpener.
-
Scalda l'acqua finchรฉ non bolle. Spegni il fuoco.
-
Posiziona l'iOpener nell'acqua calda per 2-3 minuti. Assicurati che l'iOpener sia completamente immerso nell'acqua.
-
Usa delle pinze per estrarre l'iOpener scaldato dall'acqua calda.
-
Asciuga accuratamente l'iOpener con un asciugamano.
-
Il tuo iOpener รจ pronto all'uso! Se devi scaldare di nuovo l'iOpener, scalda l'acqua fino all'ebollizione, spegni il fuoco e immergi l'iOpener in acqua per 2-3 minuti.
-
-
-
Se il vetro dello schermo รจ crepato, previeni ulteriori rotture e danni fisici durante la riparazione coprendo lo schermo con del nastro adesivo trasparente.
-
Sovrapponi strisce di nastro adesivo trasparente per coprire tutta la superficie dello schermo dellยดiPad.
-
Fai del tuo meglio per seguire il resto della guida, come descritta. In ogni caso, uno schermo crepato continuerร probabilmente a danneggiarsi durante la riparazione e, perciรฒ potrebbe essere necessario utilizzare uno strumento metallico per estrarre il vetro.
-
-
-
C'รจ una piccola fessura nell'anello adesivo dell'iPad nell'angolo in alto a destra, a circa 5 cm dal bordo superiore. Dovrai sfruttare questa debolezza.
-
Allinea lo strumento con il tasto del muto. Infila la punta di uno uno strumento di apertura in plastica nella fessura tra il vetro anteriore e il bordo in plastica. Infila solo la punta dello strumento, solo abbastanza per allargarla.
-
-
-
-
Una volta superata l'antenna WiFi (a circa da 75 mm dal bordo destro, o accanto al tasto Home), reinfila il plettro completamente.
-
Fai scorrere il plettro verso destra, rilasciando l'adesivo che fissa l'antenna WiFi al vetro anteriore.
-
L'antenna del WiFi รจ attaccata al bordo inferiore dell'iPad tramite delle viti e un cavo. Questo passaggio separa l'antenna dal pannello anteriore, assicurando che quando lo rimuoverai l'antenna non verrร danneggiata.
-
-
-
Fai scorrere il plettro sotto il bordo superiore dell'iPad, sfilandolo leggermente per aggirare la staffa della fotocamera anteriore.
-
L'adesivo in questa zona รจ molto spesso e puรฒ essere richiesta abbastanza forza. Lavora attentamente e lentamente, assicurandoti di non scivolare e danneggiare te stesso o l'iPad.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the four 2 mm Phillips #00 screws securing the LCD to the aluminum frame.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Using a plastic opening tool or a spudger, lift the right edge of the LCD out of the iPad.
-
Rotate the LCD along its left edge and lay it down on top of the front panel.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Using the tip of a spudger, peel back the piece of tape covering the LCD ribbon cable connector.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Flip up the retaining flap on the LCD ribbon cable ZIF connector.
-
Using your fingers or a pair of tweezers, pull the LCD ribbon cable from its socket on the logic board.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Without touching the front of the LCD, lift the LCD off the front panel.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Flip up the retaining flap on both of the digitizer ribbon cable ZIF connectors.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to loosen the adhesive underneath the digitizer ribbon cable.
-
Very carefully pull the digitizer ribbon cable straight out of its sockets on the logic board.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Peel back the digitizer ribbon cable and use the flat end of a spudger to release the adhesive securing the cable to the rear aluminum case.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Using your fingers, pull the digitizer ribbon cable out of its recess in the aluminum frame.
-
Remove the front panel from the iPad.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Place the iOpener in the microwave and microwave it for thirty seconds on the highest power setting.
-
Place the iOpener over the home button on the front edge of the display.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Wedge the plastic opening tool under the right side of the home button assembly and pry upwards, releasing the adhesive on that side.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Using the technique above, release the adhesive on the left side of the home button.
-
Lift the home button mount off of the front panel.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Insert the edge of plastic opening tool underneath the edge of the home button mounting bracket.
-
Slide the plastic opening tool along the retaining spring bracket, releasing the adhesive.
-
Remove the home button with mounting bracket from the front panel.
-
-
-
Segui le istruzioni per scaldare l'iOpener come descritto nella sezione sul riscaldamento dell'iOpener all'inizio di questa guida.
-
Annulla: non ho completato questa guida.
Altre 281 persone hanno completato questa guida.
24 Commenti
This was my first time fixing a Ipad 3. I've heard stories of how difficult this repair is & that i should pay someone to do it. I must say read the guide first then start the job. So far everything works and I feel confident enough to repair another ipad.
Thanks iFixit for the parts and guide.
I simply can't imagine any steps that might be taken to avoid marring the LCD while removing a cracked screen. By the time enough of the cracked screen is removed to allow protecting the LCD, it's already too late. I can't imagine a method through which removing a cracked screen wouldn't eventually become a process of troweling a stubborn sludge of adhesive and glass shards away from at least part of the perimeter of the screen recess. However, barring slight unremovable marks on my LCD resulting from the issue, I'm satisfied so far with the robustness of the the screen replacement.
It might also be useful to mention that fresh adhesive and retrieval of the camera bracket and home button assembly aren't necessary if the replacement used is iFixit's iPad 3rd Gen Front Panel Assembly, which includes those.
This is a very good and thorough guide. I have done at least 12 repairs and I have to admit that it would be nice if the glass was "always" cracked this cleanly. However, the reality is that it isn't and a lot of times the glass is completely shattered and its a very messy job just to try and get the glass off cleanly and safely. Just keep in mind that the process of actually removing the glass is going to have to be tweaked depending on the condition and type of crack you're dealing with. All the best of luck and success on future repairs!
I've been using this site now for awhile to repair various electronics. The other day i was trying to repair an Ipad 3 and was having a ton of issues getting the digitizer off so i could replace the charge port. The guide gave me great tips and suggestions just like the rest of them on the site. I was able to repair it without damaging anything else on the device. Thanks for the time and hardwork.