Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Riempi una pentola o una padella con abbastanza acqua per immergerci un iOpener.
-
Scalda l'acqua finché non bolle. Spegni il fuoco.
-
Posiziona l'iOpener nell'acqua calda per 2-3 minuti. Assicurati che l'iOpener sia completamente immerso nell'acqua.
-
Usa delle pinze per estrarre l'iOpener scaldato dall'acqua calda.
-
Asciuga accuratamente l'iOpener con un asciugamano.
-
Il tuo iOpener è pronto all'uso! Se devi scaldare di nuovo l'iOpener, scalda l'acqua fino all'ebollizione, spegni il fuoco e immergi l'iOpener in acqua per 2-3 minuti.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a SIM eject tool or an uncoiled paperclip to eject the SIM tray.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the SIM tray out of its slot and remove it from the iPad.
-
-
-
Se il vetro dello schermo è crepato, previeni ulteriori rotture e danni fisici durante la riparazione coprendo lo schermo con del nastro adesivo trasparente.
-
Sovrapponi strisce di nastro adesivo trasparente per coprire tutta la superficie dello schermo dell´iPad.
-
Fai del tuo meglio per seguire il resto della guida, come descritta. In ogni caso, uno schermo crepato continuerà probabilmente a danneggiarsi durante la riparazione e, perciò potrebbe essere necessario utilizzare uno strumento metallico per estrarre il vetro.
-
-
-
C'è una piccola fessura nell'anello adesivo dell'iPad nell'angolo in alto a destra, a circa 5 cm dal bordo superiore. Dovrai sfruttare questa debolezza.
-
Allinea lo strumento con il tasto del muto. Infila la punta di uno uno strumento di apertura in plastica nella fessura tra il vetro anteriore e il bordo in plastica. Infila solo la punta dello strumento, solo abbastanza per allargarla.
-
-
-
Una volta superata l'antenna WiFi (a circa da 75 mm dal bordo destro, o accanto al tasto Home), reinfila il plettro completamente.
-
Fai scorrere il plettro verso destra, rilasciando l'adesivo che fissa l'antenna WiFi al vetro anteriore.
-
L'antenna del WiFi è attaccata al bordo inferiore dell'iPad tramite delle viti e un cavo. Questo passaggio separa l'antenna dal pannello anteriore, assicurando che quando lo rimuoverai l'antenna non verrà danneggiata.
-
-
-
-
Fai scorrere il plettro sotto il bordo superiore dell'iPad, sfilandolo leggermente per aggirare la staffa della fotocamera anteriore.
-
L'adesivo in questa zona è molto spesso e può essere richiesta abbastanza forza. Lavora attentamente e lentamente, assicurandoti di non scivolare e danneggiare te stesso o l'iPad.
-
-
-
Svita le quattro viti a croce Phillips #00 da 2 mm che fissano il pannello LCD alla cornice in alluminio.
-
-
-
Usando la punta di uno spudger, rimuovi il pezzo di nastro che copre il connettore del cavo a nastro del pannello LCD.
-
-
-
Usa la punta di uno spudger per staccare il pezzo di nastro adesivo che fissa il cavo a nastro dello schermo touch sulla scheda logica.
-
-
-
Tira indietro e rimuovi il pezzo di nastro isolante che copre il il connettore del cavo del gruppo jack delle cuffie.
-
Usando la punta di uno spudger, solleva l'aletta di bloccaggio su entrambi i connettori ZIF che fissano il cavo jack delle cuffie alla scheda logica.
-
-
-
Tira indietro e rimuovi il pezzo di nastro adesivo che copre il connettore ZIF del cavo della scheda SIM.
-
Solleva l'aletta di bloccaggio sul connettore ZIF del cavo della scheda SIM.
-
Usando la punta di uno spudger, tira il cavo della scheda SIM dalla sua presa sulla scheda logica.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three 1.75 mm Phillips #00 screws securing the SIM board to the aluminum frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Holding the headphone jack assembly cable out of the way, remove the SIM board from the iPad.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel back and remove the adhesive tape covering the headphone jack assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 2.6 mm Phillips #0 screw securing the camera cable to the headphone jack assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the flat end of a spudger, pry the front-facing camera off of its socket on the headphone jack assembly.
-
Without removing the spudger, slide the spudger to the right, releasing the adhesive holding down the camera cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tip of the spudger, flip up the retaining flap on the microphone cable ZIF connector.
-
Insert the tip of the spudger underneath the microphone ribbon cable, removing it from its ZIF connector.
-
Slide the spudger to the left, releasing the adhesive holding the microphone ribbon cable to the headphone jack assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of the spudger to pry up the antenna connector cable out of its socket on the headphone jack assembly board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip up the retaining flap securing the volume/power button ribbon cable connector to the headphone jack assembly board.
-
Remove the volume button ribbon cable from its ZIF connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following screws from the headphone jack assembly:
-
Five 2.6 mm Phillips #0
-
Two 2.2 mm Wide Head Phillips #00
-
Two 2.6 mm Phillips #00
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Holding onto the ribbon cable of the headphone jack assembly, carefully pull the assembly parallel to the iPad, toward the bottom of the device.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasping the headphone jack assembly with both hands, pull the assembly from the iPad, minding any cables that may get caught.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following screws securing the power & volume button cable to the aluminum frame:
-
Two 5.5 mm Phillips #0
-
One 2.6 mm Phillips #0
-
Two 2.6 mm Phillips #0
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the piece of plastic covering the volume buttons.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 2.6 mm Phillips #00 screw holding the volume button frame to the aluminum frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Wedge the edge of a plastic opening tool underneath the sleep/wake sensor, being careful to not damage the fragile cable.
-
Move the plastic opening tool around the sensor, releasing the adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide a spudger underneath the power & volume cables, releasing the adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tip of the spudger rather that the wide edge, release the adhesive underneath the volume button branch of the ribbon cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Continue sliding the tip of the spudger toward the top of the iPad, releasing the adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
With the tip of the spudger still underneath the ribbon cable, gently lift the power button out of its socket in the aluminum frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Holding the power & volume button cable with with both hands, carefully pull the volume buttons and lock switch from their sockets in the aluminum frame.
-
Lift and remove the power & volume button cable out of the rear aluminum case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Wedge the tip of the plastic opening tool underneath the top side of the power button.
-
Pry the topside of the power button up off the power button bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Repeat the previous step on the underside of the power button.
-
Lift and remove the power button bracket from the power & volume button assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Wedge the tip of the plastic opening tool underneath the top side of the rotation lock/mute switch.
-
Slide the plastic opening tool downwards to pry the topside of the rotation lock/mute switch from its bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the tip of the plastic opening tool underneath the top volume rocker and pry upwards to separate it from the volume buttons bracket.
-
Repeat the procedure to separate the bottom volume rocker from the volume buttons bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift and remove the power & volume button ribbon cable.
-
Annulla: non ho completato questa guida.
Altre 6 persone hanno completato questa guida.
Un commento
Brett, if the outer power is the only thing NOT working because it does not press in (or make the clicking noise) could that be the only thing broken.
If I use a tool to push it in it works but it will go on and off intermittently. I already have the Ipad 3 apart because I am replacing the glass. Is there anyway just to replace the power button without all the other steps?