Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Riempi una pentola o una padella con abbastanza acqua per immergerci un iOpener.
-
Scalda l'acqua finché non bolle. Spegni il fuoco.
-
Posiziona l'iOpener nell'acqua calda per 2-3 minuti. Assicurati che l'iOpener sia completamente immerso nell'acqua.
-
Usa delle pinze per estrarre l'iOpener scaldato dall'acqua calda.
-
Asciuga accuratamente l'iOpener con un asciugamano.
-
Il tuo iOpener è pronto all'uso! Se devi scaldare di nuovo l'iOpener, scalda l'acqua fino all'ebollizione, spegni il fuoco e immergi l'iOpener in acqua per 2-3 minuti.
-
-
-
Se il vetro dello schermo è crepato, previeni ulteriori rotture e danni fisici durante la riparazione coprendo lo schermo con del nastro adesivo trasparente.
-
Sovrapponi strisce di nastro adesivo trasparente per coprire tutta la superficie dello schermo dell´iPad.
-
Fai del tuo meglio per seguire il resto della guida, come descritta. In ogni caso, uno schermo crepato continuerà probabilmente a danneggiarsi durante la riparazione e, perciò potrebbe essere necessario utilizzare uno strumento metallico per estrarre il vetro.
-
-
-
C'è una piccola fessura nell'anello adesivo dell'iPad nell'angolo in alto a destra, a circa 5 cm dal bordo superiore. Dovrai sfruttare questa debolezza.
-
Allinea lo strumento con il tasto del muto. Infila la punta di uno uno strumento di apertura in plastica nella fessura tra il vetro anteriore e il bordo in plastica. Infila solo la punta dello strumento, solo abbastanza per allargarla.
-
-
-
Una volta superata l'antenna WiFi (a circa da 75 mm dal bordo destro, o accanto al tasto Home), reinfila il plettro completamente.
-
Fai scorrere il plettro verso destra, rilasciando l'adesivo che fissa l'antenna WiFi al vetro anteriore.
-
L'antenna del WiFi è attaccata al bordo inferiore dell'iPad tramite delle viti e un cavo. Questo passaggio separa l'antenna dal pannello anteriore, assicurando che quando lo rimuoverai l'antenna non verrà danneggiata.
-
-
-
-
Fai scorrere il plettro sotto il bordo superiore dell'iPad, sfilandolo leggermente per aggirare la staffa della fotocamera anteriore.
-
L'adesivo in questa zona è molto spesso e può essere richiesta abbastanza forza. Lavora attentamente e lentamente, assicurandoti di non scivolare e danneggiare te stesso o l'iPad.
-
-
-
Svita le quattro viti a croce Phillips #00 da 2,0 mm che fissano il pannello LCD alla copertura posteriore.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If present, remove the piece of tape covering the end of the front facing camera cable with a pair of tweezers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to carefully pry the connector up from its socket on the control board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to separate the adhesive securing the front facing camera cable to the control board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pry the front-facing camera up off the foam adhesive securing it to the rear case.
-
Remove the front-facing camera.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a pair of tweezers to remove the rubber cover up off the rear-facing camera housing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 3.3 mm Phillips screw from the rear-facing camera metal retainer clip.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the rear-facing camera metal retainer clip straight up from its recess in the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a plastic opening tool to pry the rear-facing camera connector up from its socket on the control board.
-
Remove the rear-facing camera.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 2.1 mm Phillips screw from the rear-facing camera housing.
-
Remove the camera housing from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to flip up the retaining flap on the button assembly ribbon cable ZIF socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Run the tip of a spudger underneath the button assembly cable to free it from the socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to flip up the retaining flap on the microphone ribbon cable ZIF socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the microphone ribbon cable straight out with a pair of tweezers.
-
Gently bend the cable to keep it out of the way.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 2.9 mm Phillips screws securing the headphone jack to the rear case.
-
Pull the headphone jack from its port in the rear case and fold out of the way.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 2.1 mm Phillips screws securing the metal bracket to the rear case.
-
Remove the metal bracket from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If present, use tweezers to remove the piece of tape covering the end of the headphone jack/control board cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to flip up the retaining flap on the headphone jack/control board cable ZIF socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the tip of a spudger underneath the ribbon cable to disconnect it.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently peel the headphone jack/control board ribbon cable away from the rear case to free it from the adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to loosen the adhesive under the narrower part of the ribbon cable near the headphone jack.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the flat end of a spudger under the middle portion of the ribbon cable to separate the adhesive holding it to the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the flat end of a spudger under the widest part of the cable to free it from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
To begin freeing it from adhesive, pry gently under the control board near the front-facing camera socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pry gently under the control board near the rear-facing camera.
-
Carefully pry under the widest part of the board to free the assembly from the last of the adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the headphone jack assembly from the case.
-
Annulla: non ho completato questa guida.
Altre 15 persone hanno completato questa guida.