Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Riempi una pentola o una padella con abbastanza acqua per immergerci un iOpener.
-
Scalda l'acqua finché non bolle. Spegni il fuoco.
-
Posiziona l'iOpener nell'acqua calda per 2-3 minuti. Assicurati che l'iOpener sia completamente immerso nell'acqua.
-
Usa delle pinze per estrarre l'iOpener scaldato dall'acqua calda.
-
Asciuga accuratamente l'iOpener con un asciugamano.
-
Il tuo iOpener è pronto all'uso! Se devi scaldare di nuovo l'iOpener, scalda l'acqua fino all'ebollizione, spegni il fuoco e immergi l'iOpener in acqua per 2-3 minuti.
-
-
-
Se il vetro dello schermo è crepato, previeni ulteriori rotture e danni fisici durante la riparazione coprendo lo schermo con del nastro adesivo trasparente.
-
Sovrapponi strisce di nastro adesivo trasparente per coprire tutta la superficie dello schermo dell´iPad.
-
Fai del tuo meglio per seguire il resto della guida, come descritta. In ogni caso, uno schermo crepato continuerà probabilmente a danneggiarsi durante la riparazione e, perciò potrebbe essere necessario utilizzare uno strumento metallico per estrarre il vetro.
-
-
-
C'è una piccola fessura nell'anello adesivo dell'iPad nell'angolo in alto a destra, a circa 5 cm dal bordo superiore. Dovrai sfruttare questa debolezza.
-
Allinea lo strumento con il tasto del muto. Infila la punta di uno uno strumento di apertura in plastica nella fessura tra il vetro anteriore e il bordo in plastica. Infila solo la punta dello strumento, solo abbastanza per allargarla.
-
-
-
-
Una volta superata l'antenna WiFi (a circa da 75 mm dal bordo destro, o accanto al tasto Home), reinfila il plettro completamente.
-
Fai scorrere il plettro verso destra, rilasciando l'adesivo che fissa l'antenna WiFi al vetro anteriore.
-
L'antenna del WiFi è attaccata al bordo inferiore dell'iPad tramite delle viti e un cavo. Questo passaggio separa l'antenna dal pannello anteriore, assicurando che quando lo rimuoverai l'antenna non verrà danneggiata.
-
-
-
Fai scorrere il plettro sotto il bordo superiore dell'iPad, sfilandolo leggermente per aggirare la staffa della fotocamera anteriore.
-
L'adesivo in questa zona è molto spesso e può essere richiesta abbastanza forza. Lavora attentamente e lentamente, assicurandoti di non scivolare e danneggiare te stesso o l'iPad.
-
-
-
Svita le quattro viti a croce Phillips #00 da 2,0 mm che fissano il pannello LCD alla copertura posteriore.
-
-
-
Usa la parte piatta di uno strumento di apertura in plastica per ruotare attentamente verso l'alto le alette di bloccaggio sulle due prese ZIF del cavo a nastro del digitizer.
-
-
-
Solleva il pannello LCD dal suo lato lungo lontano dal cavo del digitizer e ruotalo delicatamente verso la copertura posteriore, come per chiudere un libro.
-
Mentre tieni sollevato il pannello LCD, sfila delicatamente il pannello anteriore lontano dall'iPad. Stai attento a non far impigliare il cavo del digitizer sulla copertura posteriore o sul pannello LCD.
-
Appoggia il pannello LCD nel corpo dell'iPad per sicurezza.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the LCD from its long edge closest to the volume buttons and gently flip it out of the rear case—like turning the page in a book.
-
Set the LCD face down on a clean surface. You may want to rest it on a soft cloth to prevent scratches.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a plastic opening tool to lift the display data cable lock upwards.
-
Pull the display data cable out of its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the LCD assembly from the rear panel assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If present, remove the piece of tape on the dock connector cable with a plastic opening tool.
-
Use the edge of a plastic opening tool to carefully pry the dock connector cable's connector up from its socket on the logic board.
-
Peel the dock connector ribbon cable off the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pry the speaker cable connector straight up from its socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following screws:
-
Two 2.1 mm Phillips screws securing one of two metal brackets to the rear case.
-
One 2.6 mm Phillips screw securing the logic board to the rear case.
-
Remove the metal bracket from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If present, use tweezers to remove the piece of tape covering the end of the headphone jack/control board cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to flip up the retaining flap on the headphone jack/control board cable ZIF socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the tip of a spudger underneath the headphone jack/control board ribbon cable to disconnect it.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 2.1 mm Phillips screws securing the second metal bracket to the rear case near the digitizer cable socket.
-
Remove the metal bracket from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the edge of a plastic opening tool to gently pry the logic board up from the adhesive securing it to the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the logic board out from the rear case and flip it over toward the battery.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the tip of a spudger to pry the Wi-Fi antenna connector up from its socket on the logic board.
-
Remove the logic board from the case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Move the dock connector/speaker cables out of the way and peel the Bluetooth/Wi-Fi antenna cable off the adhesive securing it to the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following screws securing the Bluetooth/Wi-Fi antenna to the rear case:
-
Two 1.7 mm Phillips screws
-
Two 2.0 mm Phillips screws
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel the Bluetooth/Wi-Fi antenna off the speaker enclosure and remove it from the iPad 2.
-
Annulla: non ho completato questa guida.
Altre 35 persone hanno completato questa guida.
Un commento
I’ve seen other guides that avoid having to remove the entire logic board by just popping the metal shield over the WiFi board on the bottom part of the logic board then popping out the WiFi board with the antenna cable attached. I assume there’s some good reason for not using this approach? Is there some risk of damaging the WiFi board? It’s just a press fit into the base of the logic board and there’s sufficient clearance to thread the antenna cable up from the bottom and out thru the space where the WiFi board goes. The metal shield can be pried off and pushed back on without damaging it, and the WiFi board can be eased up from it’s socket with the tip of an exacto knife blade. Removing the entire logic requires that it be re-seated so the metal contacts at each end mate and requires an adhesive to hold it in place. What’s wrong with this alternative?