Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Riempi una pentola o una padella con abbastanza acqua per immergerci un iOpener.
-
Scalda l'acqua finché non bolle. Spegni il fuoco.
-
Posiziona l'iOpener nell'acqua calda per 2-3 minuti. Assicurati che l'iOpener sia completamente immerso nell'acqua.
-
Usa delle pinze per estrarre l'iOpener scaldato dall'acqua calda.
-
Asciuga accuratamente l'iOpener con un asciugamano.
-
Il tuo iOpener è pronto all'uso! Se devi scaldare di nuovo l'iOpener, scalda l'acqua fino all'ebollizione, spegni il fuoco e immergi l'iOpener in acqua per 2-3 minuti.
-
-
-
Se il vetro dello schermo è crepato, previeni ulteriori rotture e danni fisici durante la riparazione coprendo lo schermo con del nastro adesivo trasparente.
-
Sovrapponi strisce di nastro adesivo trasparente per coprire tutta la superficie dello schermo dell´iPad.
-
Fai del tuo meglio per seguire il resto della guida, come descritta. In ogni caso, uno schermo crepato continuerà probabilmente a danneggiarsi durante la riparazione e, perciò potrebbe essere necessario utilizzare uno strumento metallico per estrarre il vetro.
-
-
-
C'è una piccola fessura nell'anello adesivo dell'iPad nell'angolo in alto a destra, a circa 5 cm dal bordo superiore. Dovrai sfruttare questa debolezza.
-
Allinea lo strumento con il tasto del muto. Infila la punta di uno uno strumento di apertura in plastica nella fessura tra il vetro anteriore e il bordo in plastica. Infila solo la punta dello strumento, solo abbastanza per allargarla.
-
-
-
Una volta superata l'antenna WiFi (a circa da 75 mm dal bordo destro, o accanto al tasto Home), reinfila il plettro completamente.
-
Fai scorrere il plettro verso destra, rilasciando l'adesivo che fissa l'antenna WiFi al vetro anteriore.
-
L'antenna del WiFi è attaccata al bordo inferiore dell'iPad tramite delle viti e un cavo. Questo passaggio separa l'antenna dal pannello anteriore, assicurando che quando lo rimuoverai l'antenna non verrà danneggiata.
-
-
-
-
Fai scorrere il plettro sotto il bordo superiore dell'iPad, sfilandolo leggermente per aggirare la staffa della fotocamera anteriore.
-
L'adesivo in questa zona è molto spesso e può essere richiesta abbastanza forza. Lavora attentamente e lentamente, assicurandoti di non scivolare e danneggiare te stesso o l'iPad.
-
-
-
Svita le quattro viti a croce Phillips #00 da 2,0 mm che fissano il pannello LCD alla copertura posteriore.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully peel the rubber cover off the metal camera retainer and remove it from the iPad 2.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following two screws:
-
One 3.3 mm Phillips screw
-
One 2.1 mm Phillips screw
-
Lift the metal retainer clip straight up from its recess in the rear panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a plastic opening tool to pry the rear camera connector up from its socket on the control board.
-
Remove the rear facing camera.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following screws from the volume/power button assembly cable:
-
Two 2.5 mm Phillips #000 screws, at a 45º angle securing the power button.
-
Two 5 mm Phillips #000 screws
-
One 2 mm Phillips #000 screw at a 45º angle.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the metal bracket securing the rotation lock/silent switch.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the power button cable out of the recess in the rear case and bend it out of the way.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the sleep/power button from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the center screw hole of the volume control bracket to tilt it out toward the edge of the case and then pull it up out of its recess.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently peel the power button portion of the cable away from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently lift the cable between the power button and volume rocker up off of the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Bend the cable toward the inside of the rear case, but do not attempt to remove it as it is still connected to the upper component board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the rotation lock/silent switch from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the tip of a spudger to push the volume rocker into the interior of the rear case.
-
Remove the volume rocker from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the point of an opening pick to gently peel the Smart Cover sleep/wake sensor up off the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully peel the volume rocker portion of the button cable away from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently peel the last vertical portion off of the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single 2 mm Phillips #000 screw from the lower end of the upper component board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a set of tweezers to remove the foam block from between the rear case and the upper component board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a spudger under the end of the upper component board and gently slide it toward the volume rocker to free the board from adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a spudger under the upper left end of the upper component board and lift it up off of its adhesive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip up the retaining bar securing the upper component board cable connector.
-
Pull the connector straight out of its socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the end of the upper component board cable up off of the adhesive holding it to the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the tip of a spudger under the upper component board to lift it slightly.
-
Pull the board up and out of the space between the battery and the rear case bezel.
-
Remove the upper component board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel the tape covering the button cable connector off of the upper component board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the button cable connector straight up off of its connector on the upper component board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel the power button off of the power button bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the point of an opening pick between the rotation lock/silent switch and its bracket to sever the adhesive there.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the opening pick under the remaining portion of the rotation lock/silent switch to peel it up off the button bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the point of the opening pick to peel the mechanical volume buttons up from the bracket.
-
Remove the button cable assembly from the button bracket.
-
Annulla: non ho completato questa guida.
Altre 60 persone hanno completato questa guida.
Un commento
ipad was dropped on it's volume button, bending the metal around the volume button. Causing the ipad to permanently reduce volume. cover removed ok, no damage incurred. important to remember that bottom and left hand side to not stick instruments in very far to avoid electrical devices such as the wifi adapter approx 2mm. re-bent case which relieved the pressure. all working ok now