Aggiusta la tua roba Comunità Store

iMac Intel 24" EMC 2134 and 2211 Display Panel Replacement

Solo Prerequisita
Questa guida è destinata a essere usata solo come prerequisito per altre guide. Da sola è incompleta.

Introduzione

Remove your display panel to gain access to the hard drive, optical drive, and power supply.

Cosa ti serve

  1. iMac Intel 24" EMC 2134 and 2211 Display Panel Replacement, Display Panel: passo 1, immagine 1 di 2 iMac Intel 24" EMC 2134 and 2211 Display Panel Replacement, Display Panel: passo 1, immagine 2 di 2

    • Disconnect the LCD temperature sensor by pulling the connector straight out of its socket on the logic board.

    • If necessary, de-route the LCD temperature sensor cable from behind the logic board.

    Modifica

  2. iMac Intel 24" EMC 2134 and 2211 Display Panel Replacement: passo 2, immagine 1 di 1

    • Remove the two 5.3 mm T6 Torx screws securing the display data cable to the logic board.

    Modifica

  4. iMac Intel 24" EMC 2134 and 2211 Display Panel Replacement: passo 3, immagine 1 di 1

    • Disconnect the display data cable connector from its socket on the logic board by pulling the attached plastic tab towards you and away from the iMac.

    Modifica

  5. iMac Intel 24" EMC 2134 and 2211 Display Panel Replacement: passo 4, immagine 1 di 2 iMac Intel 24" EMC 2134 and 2211 Display Panel Replacement: passo 4, immagine 2 di 2

    • Lay the iMac down on a table before you remove the LCD so that it doesn't fall.

    • Remove the eight 12 mm T8 Torx screws securing the display panel to the rear case.

    • Lift the right side of the display panel a few inches up from the iMac.

    • Do not lift the LCD all the way up; there are still connectors attaching the LCD to the internals.

    Modifica

  6. iMac Intel 24" EMC 2134 and 2211 Display Panel Replacement: passo 5, immagine 1 di 2 iMac Intel 24" EMC 2134 and 2211 Display Panel Replacement: passo 5, immagine 2 di 2

    • With the LCD lifted, disconnect the LCD cable by pulling down.

    • The LCD cable is attached to the underside of the power supply; be careful where you put your fingers so you don't get zapped by a capacitor.

    • On reassembly, you may find it helpful to remove the power supply, reconnect the LCD power cable, and then reinstall the power supply.

    • Alternatively, the LCD power cable can be disconnected from the LCD, rather than the power supply.

    Modifica

  7. iMac Intel 24" EMC 2134 and 2211 Display Panel Replacement: passo 6, immagine 1 di 2 iMac Intel 24" EMC 2134 and 2211 Display Panel Replacement: passo 6, immagine 2 di 2

    • Continue to lift the LCD from the right side.

    • Remove the LCD.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 4 persone hanno completato questa guida.

Autore

con 9 altri collaboratori

Brittany McCrigler

Membro da: 03/05/12

89.014 Reputazione

131 Guide realizzate

Distintivi: 48

+45 altri distintivi

Team

iFixit Membro di iFixit

Staff

135 Membri

16.817 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 2

Tutti i Tempi: 2,928