Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Poggiare l'iMac sul lato anteriore su un tavolo, con il bordo inferiore rivolto verso l'utente.
-
Allentare la vite con testa a croce al centro dello sportello di accesso.
-
Rimuovere lo sportello di accesso dall'iMac.
-
-
-
Rimuovere le 12 viti seguenti, che fissano la mascherina anteriore al case posteriore:
-
Otto viti Torx T8 da 13 mm.
-
Quattro viti Torx T8 da 25 mm.
-
-
-
Sollevare delicatamente la mascherina dal bordo superiore, lontano dal case posteriore.
-
Dopo aver rimosso il bordo superiore della mascherina anteriore dal case posteriore, ruotare la mascherina verso la staffa ed estrarla dal case posteriore.
-
Ruotare la mascherina anteriore lontano dal resto del dispositivo e adagiarla sul bordo superiore dell'iMac.
-
-
-
Estrarre il connettore del sensore temperatura dell'LCD direttamente dal connettore sulla scheda logica.
-
(nella parte superiore della scheda logica nel modello da 24")
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single T10 Torx screw securing the right speaker to the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the right speaker cable connector from the audio board by pulling it straight up from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently lift the right speaker out of the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the optical drive fan connector from the audio board by pulling it straight away from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently lift the optical drive fan off the plastic posts protruding from the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the flat end of a spudger into the gap between the optical drive data cable connector and its socket.
-
Twist the spudger to separate the connector from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the microphone cable connector from the audio board by pulling it straight up from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the following connectors:
-
Hard drive thermal sensor cable.
-
Optical drive thermal sensor cable.
-
Hard drive fan cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the DC-in cable by simultaneously depressing both locking arms and pulling its connector away from the socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
Attrezzo utilizzato in questo passaggio:Metal Spudger$2.99-
Pull the SATA data cable straight up off the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry both antenna connectors up off the AirPort Extreme card.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the left speaker connector from the audio board by pulling it straight away from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
De-route the left fan cable from the channel on the CPU fan.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the following connectors:
-
Ambient temperature sensor cable.
-
Power button cable.
-
CPU fan cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the camera cable connector from the logic board by pulling it straight up from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry the bluetooth antenna connector up off the bluetooth board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the sharp end of a spudger to peel the EMI tape off the headphone/microphone jacks.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following screws securing the logic board to the rear case:
-
Three fine-thread T10 Torx.
-
Six coarse-thread T10 Torx.
-
One longer coarse-thread T10 Torx.
-
Two coarse-thread T8 Torx.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the logic board assembly out of the rear case, minding any cables or I/O ports that may get caught.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently lift the hard drive fan off the plastic pins protruding from the lower case.
-
Annulla: non ho completato questa guida.
Altre 3 persone hanno completato questa guida.