Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Orient the iMac face-side down on a table with the bottom edge facing yourself.
-
Remove the two Phillips screws securing the access door to the bottom grille of your iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three T8 Torx screws securing the front bezel to the rear case along the lower edge of the iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the computer over.
-
Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
Attrezzo utilizzato in questo passaggio:Plastic Cards$2.99-
Insert a plastic card up into the corner of the air vent slot near the top of the rear case.
-
Push the card toward the top of the iMac to release the front bezel latch.
-
Pull the front bezel away from the rear case.
-
Repeat this process for the other side of the front bezel.
-
If the bezel refuses to release, try pressing the lower edge back onto the rear case and repeat this opening process.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lay your iMac stand-side down on a table.
-
Lift the front bezel from its lower edge and rotate it away from the rest of your iMac, minding the RAM arms that may get caught.
-
Lay the front bezel above the rest of the iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If necessary, remove the piece of kapton tape wrapped around the microphone and camera connectors.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect both the camera and microphone cables.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel the lower EMI shield off the lower edge of the iMac and off the two vertical 4" sections on either side of the iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Tape the lower EMI shield up against the face of the display to keep it out of the way while you work.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two T6 Torx screws securing the display data cable connector to the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
To disconnect the display data cable, grab its connector's black tab and pull it away from the face of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel back the two EMI tape strips from the left and right edges of the display.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four recessed T10 Torx screws securing the display to the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the lower edge of the display slightly out of the rear case.
-
Disconnect both inverter cables (shown in red) by pulling their connectors toward the bottom edge of your iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the display until it is nearly perpendicular to the rear case.
-
Disconnect the remaining two inverter cables (shown in red) by pulling their connectors toward the top edge of your iMac.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
While holding the display perpendicular to the rear case, pull it upward to peel off the EMI shield stuck to its upper edge.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the IR board cable by pulling its connector away from the socket on the IR board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two T6 Torx screws securing the IR board bracket to the IR board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
De-route the IR cable from under the aluminum heat sink and tuck it behind the optical drive to keep it out of the way.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single T10 Torx screw securing the left speaker to the rear case.
-
Lift the left speaker out of the rear case and de-route its cable across the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single T10 Torx screw securing the right speaker to the rear case.
-
Lift the right speaker out of the rear case, minding the short cable between the speaker and its connector (located slightly above the right speaker).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the speakers from the logic board by pulling their connector toward the top edge of the iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two Phillips or two T6 Torx screws securing the AirPort/Bluetooth board to the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your finger to lift the AirPort/Bluetooth board from its left edge, disconnecting it from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry both antenna cable connectors up off the AirPort/Bluetooth board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the DC-in cable by simultaneously depressing both locking arms and pulling its connector away from the socket on the logic board toward the top of your iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the ambient light sensor by pulling its connector away from the face of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the optical drive fan from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the IR/camera cable from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the optical drive thermal sensor cable from the logic board by pulling its connector toward the left edge of the iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two T6 Torx screws securing the optical drive connector to the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry the optical drive connector up off the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the CPU fan from the logic board by pulling its connector toward the top edge of the iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the hard drive thermal sensor from the logic board by pulling its connector toward the top edge of the iMac.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the hard drive fan by pulling its connector away from the face of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the power button cable by pulling its connector away from the face of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two T6 Torx screws near the top of the heat sinks.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following seven screws securing the logic board to the rear case:
-
Three coarse-thread T10 Torx.
-
Three fine-thread T10 Torx.
-
One long coarse-thread T10 Torx.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Tuck the RAM arms into the iMac so they rest on the perforated metal grille along its lower edge.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the top of the logic board toward yourself slightly.
-
Pull the right edge of the logic board toward yourself slightly to free the I/O ports from the rear case, being careful not to bend the board.
-
Continue rotating the board toward yourself until you have enough room to reach the SATA connector, shown in the next step.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Continue rotating the board toward yourself until you have enough room to reach the SATA connector (shown in red).
-
Insert the blunt end of a metal spudger between the SATA connector and its socket. Twist the shaft of the metal spudger to separate the connector from its socket.
-
Disconnect the SATA cable from the logic board.
-
Lift the logic board out of the rear case by its edges, minding any cables that may get caught.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If necessary, remove the yellow kapton tape covering the AC-in cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a pair of tweezers to pull the AC-in cable out from underneath the chassis.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the AC-in cable by depressing the lock mechanism while pulling the connector away from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four T10 Torx screws securing the power supply to the rear case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the power supply out of the rear case, minding the AC-in cable that may get caught.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
While holding the power supply by its edges with one hand, use your other hand to disconnect the DC-DC cable connector near the left edge of the power supply.
-
Annulla: non ho completato questa guida.
Altre 40 persone hanno completato questa guida.
5 Commenti
The images on this stage show the heat shield, cpu and associated pipework as removed but these steps are not included in the inbstructions
Sorry about that, the guide should be fixed now.
Step 40 Sorry, I didn't notice that someone had already commented. The fine threaded (orange) and course threaded (red) screws at the bottom of the machine are reversed. Just need to switch the circles on these two. Anybody know how to work with the images for the manual?