iMac G3 Model M4984 Hard Drive Replacement

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Introduzione

The iMac G3 Uses a 3.5" IDE Hard Drive. It supports data partitions no larger then 128GB and boot partitions no larger then 8GB (The 8GB limit only applies to iMac G3 tray loaders).

Cosa ti serve

Passo 1 Logic Board

iMac G3 Model M4984 Hard Drive Replacement, Logic Board: passo 1, immagine 1 di 1

The iMac G3. This was a great computer for the time, and had plenty of features.

Traduci

Passo 2

Start by flipping the iMac upside-down. It may help to lay it on a towel, so you don't damage the screen, or scratch the face.

Traduci

Passo 3

iMac G3 Model M4984 Hard Drive Replacement: passo 3, immagine 3 di 3

Remove this Phillips screw.
Using a flathead screwdriver, work your way around the bottom cover, until it comes off.
Then, lift the bottom cover up and out, and set it aside.

Traduci

Passo 4

iMac G3 Model M4984 Hard Drive Replacement: passo 4, immagine 3 di 3

Now, remove the DB-15 Video connector from the logic board.
It may be helpful to use a Phillips screwdriver to remove the thumbscrews.

Traduci

Passo 5

iMac G3 Model M4984 Hard Drive Replacement: passo 5, immagine 3 di 3

Remove the power cable from the logic board assembly.

Traduci

Passo 6

Remove the front panel connector. (You may also need to remove an additional screw that connects the front panel connector to the logic board assembly).

Traduci

Passo 7

iMac G3 Model M4984 Hard Drive Replacement: passo 7, immagine 3 di 3

Now, remove these Phillips screws.
Now, grab the logic board assembly by the piece of plastic, and lift it out.

Traduci

Passo 8

The logic board assembly. This is the heart of the computer, it contains the motherboard, CPU, RAM, V-RAM, PRAM battery, the hard drive, and the optical drive.

Traduci

Passo 9 Optical Drive

iMac G3 Model M4984 Hard Drive Replacement, Optical Drive: passo 9, immagine 1 di 1

Now to remove the optical drive!

Traduci

Passo 10

The optical drive is located near the front of the assembly.

Traduci

Passo 11

iMac G3 Model M4984 Hard Drive Replacement: passo 11, immagine 3 di 3

To remove the drive, push it in, lift up, and then pull forward.
As you pull the drive forward, disconnect the ribbon cable and set it aside.

Traduci

Passo 12

iMac G3 Model M4984 Hard Drive Replacement: passo 12, immagine 3 di 3

Remove the two phillips #00 screws.
Then remove the board. This will reveal that it is a standard PATA drive.
Congrats, the drive is free! You can use any PATA-tray loading drive in the iMac G3 which means you can install a CDRW to burn CDs in OS9 or X(if using OSX,install that DVD writer) but, of course only original drives will match the great look of the iMac).

Traduci

Passo 13 Hard Drive

iMac G3 Model M4984 Hard Drive Replacement, Hard Drive: passo 13, immagine 1 di 1

Hard Drive Removal:

Traduci

Passo 14

Start by removing these Phillips screws:
Now, remove all of these cables:

Traduci

Passo 15

Now, remove the optical drive retention spring.
Push in on both sides, and pull towards you releasing the retention spring.
It may help to do it one side at a time.

Traduci

Passo 16

iMac G3 Model M4984 Hard Drive Replacement: passo 16, immagine 3 di 3

Now lift the drive up, and pull it out.
Make sure that no cables are snagged before completed pulling out the drive!

Traduci

Passo 17

When installing a new drive, make sure that the drive jumper block is set to "Single drive". In most drives, this means removing the jumper, or positioning the jumper horizontally instead of vertically, so you don't lose it.
To remove the drive from the metal caddy, remove these four screws from the side of the drive.

Traduci