Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Solo Prerequisita
Questa guida è destinata a essere usata solo come prerequisito per altre guide. Da sola è incompleta.

Cosa ti serve

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 1, immagine 1 di 3 : passo 1, immagine 2 di 3 : passo 1, immagine 3 di 3
    • Only follow the next 9 steps if you are replacing your hard drive with an SSD kit.

    • Depress the enclosure's front plate latch with your finger. While holding the latch down, swing the plate out.

    • Remove the front plate.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 3 : passo 2, immagine 2 di 3 : passo 2, immagine 3 di 3
    • Line up the small SATA connectors so that the narrow side of the connector on the SSD matches the narrow side on the enclosure connector.

    • Slide the drive in through the front of the enclosure until the SATA connector is fully seated.

    • The SSD's ports connect with the enclosure in only one way. If the ports are not lining up, rotate the SSD and try again.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 1
    • You may optionally install two Philips #1 screws that came with the enclosure kit to secure the SSD in the enclosure.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 2 : passo 4, immagine 2 di 2
    • Plug the included sensor-enabled SATA power cable into the wide side of the enclosure's SATA connector.

    • The cable is keyed to connect in only one way. If you can't connect the cable, rotate it 180°, and try again.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 3 : passo 5, immagine 2 di 3 : passo 5, immagine 3 di 3
    • Peel the backing off of the adhesive back of the small temperature sensor board.

    • Adhere the temperature sensor board to an exposed, metal area of the surface of the SSD, as close as possible to the SATA connector.

    • Fold the excess temperature sensor wires so that they are out of the way while you install the enclosure.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 1
    • Install the mounting pins from the old hard drive onto the sides of the enclosure.

    • The holes on the enclosure may not be threaded, so screwing the mounting pins into them may require extra effort. Take your time and screw them in slowly, making sure they go in straight.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 2 : passo 7, immagine 2 di 2
    • Attach any mounting brackets removed from the old hard drive onto the enclosure.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 2 : passo 8, immagine 2 di 2
    • Connect the iMac's SATA power cable to the new temperature-capable SATA power cable.

    • Route the SATA cables where they will not interfere with any other components.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 2 : passo 9, immagine 2 di 2
    • Connect the iMac's SATA data cable to the enclosure's SATA data connector.

Linea Traguardo

Altre 8 persone hanno completato questa guida.

Arthur Shi

Membro da: 01/03/18

248.451 Reputazione

503 Guide realizzate

Team

iFixit Membro di iFixit

Staff

136 Membri

16.573 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 22

Ultimi 30 Giorni: 109

Tutti i Tempi: 7,563