Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

iHome iH27B Main Motherboard Replacement

Cosa ti serve

  1. iHome iH27B Main Motherboard Replacement, Outer Case: passo 1, immagine 1 di 1

    • Remove any iPod or apple music device connected to the iHome and unplug from any power source.

    • Flip the iHome so the speakers are laying on a flat surface, and you have the concealed battery areas facing you.

    Traduci

  2. iHome iH27B Main Motherboard Replacement: passo 2, immagine 1 di 3 iHome iH27B Main Motherboard Replacement: passo 2, immagine 2 di 3 iHome iH27B Main Motherboard Replacement: passo 2, immagine 3 di 3

    • Using your fingers, press down firmly on the plastic slide and push in the direction of the arrows shown above the word "Open" on the plastic.

    • Remove the plastic slide from its location and set it aside.

    • These plastic slides are not interchangeable, so make sure each goes back to its original location in reassembly.

    • Remove all 4 AA batteries by placing your fingernail at one end of the battery and applying force upwards until the battery is freed from its holder.

    • Insert your fingernail or a prying tool under the notch of the plastic slide that is protecting the watch battery.

    • Set the plastic covering and the watch battery aside.

    Traduci

  3. iHome iH27B Main Motherboard Replacement: passo 3, immagine 1 di 1

    • Remove the following screws:

    • Eight 10 mm using the Phillips #0 on the bottom of your device.

    • Cataloging each screw by size in plastic bags or separate places on a flat surface will make them easier to find when reassembling.

    Traduci

  5. iHome iH27B Main Motherboard Replacement: passo 4, immagine 1 di 1

    • Use your fingers or a plastic opening tool to carefully pry apart the plastic connections still connecting the base to the top.

    • Be careful not to pry too hard. Cracking the plastic connections could make reassembly harder.

    Traduci

  6. iHome iH27B Main Motherboard Replacement: passo 5, immagine 1 di 1

    • Slowly lift the plastic base towards you and lay it on the flat surface. The base should still be connected to the rest of the iHome by a few wires.

    • You should have visible access to most of the components inside the iHome now.

    Traduci

  7. iHome iH27B Main Motherboard Replacement, AV circuit board: passo 6, immagine 1 di 1

    • Remove the following screws:

    • Two 10 mm Phillips #0

    Traduci

  8. iHome iH27B Main Motherboard Replacement: passo 7, immagine 1 di 1

    • Pull out the AV circuit board and lift it up and out of the way to allow access to other components.

    Traduci

  9. iHome iH27B Main Motherboard Replacement, Main Motherboard: passo 8, immagine 1 di 1

    • Remove the following screws:

    • Two 10 mm Phillips #0

    • Pull the speakers away and set them aside for now. They should still be connected to the rest of the iHome by two wires.

    Traduci

  10. iHome iH27B Main Motherboard Replacement: passo 9, immagine 1 di 1

    • Remove the following 6 screws:

    • Two 7 mm Phillips #0

    • Three 10 mm Phillips #2

    • One 9 mm Phillips #2

    • Set the screws aside, careful to not mix them up with your other screws.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 5 altri collaboratori

John Kraemer

Membro da: 10/09/12

76 Reputazione

9 Guide realizzate

Distintivi: 7

+4 altri distintivi

Team

Cal Poly, Team 3-21, Amido Fall 2012 Membro di Cal Poly, Team 3-21, Amido Fall 2012

CPSU-AMIDO-F12S3G21

4 Membri

9 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 837