Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a coin to rotate the battery locking screw 90 degrees clockwise.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.
-
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Push the wire clasp away from the AirPort card and toward the display, then rotate up to free it from the RAM shield.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the clear plastic tab on the AirPort card and pull toward the display.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Hold the AirPort card in one hand and use your other hand to remove the antenna cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four silver Phillips screws that secure the RAM shield.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the metal bracket on top of the RAM shield and pull upward to remove the shield.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a pin (or anything you like) to remove the three rubber feet from the lower case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three newly-revealed Phillips screws.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three hex screws using a T8 Torx screwdriver (or Allen screws using an Allen key if these are used).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two Phillips screws on either side of the battery contacts.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Push the thin rims of the lower case surrounding the battery compartment in, bending them past the tabs, and then lift up to free that corner of the lower case.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Once the front and sides of the lower case are free, turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free (it may be helpful to jiggle the case up and down).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the small greasy springs with white plastic caps from either side of the battery contacts.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 10 screws from the bottom shield:
-
Six 3 mm Phillips
-
Three 7.5 mm Phillips
-
One 14 mm Phillips
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single Phillips screw securing the DC-In board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the DC-In cable from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Deroute the cable from around the optical drive, removing tape as necessary, and angle the DC-In board out of its compartment.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 11 screws from the bottom of the computer:
-
Three 3 mm Phillips around the battery compartment. (Some models may only have two screws.)
-
Three 4.5 mm Phillips along the optical drive bezel. (a magnetic screwdriver may help to lift these screws out)
-
One 11 mm Phillips in the lower right corner. (if present)
-
Four 14.5 mm Phillips.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn over the computer and open it.
-
Remove the 2 Phillips screws (3mm) from the edges of the keyboard area.
-
Remove the 4 mm Phillips screw from the lower left corner.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the upper case and use a spudger or your finger to disconnect the trackpad connector hidden beneath the white plastic tab. Due to model variatons your trackpad connector may be different than the one pictured.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully lift the upper case about half of an inch and move it so that you can access the power and speaker cables.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the upper case enough to disconnect the blue and white power cable from the logic board. Using your fingernails or a dental pick, carefully pry the connector from its socket. Make sure you're pulling only on the connector and not on the socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully disconnect the multicolored speaker cable from the logic board. As before, make sure you're pulling only on the connector and not on the socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 16 screws:
-
Thirteen 3 mm Phillips.
-
One 3 mm Phillips. (actual screw not present in image)
-
Two 4 mm Phillips.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the top shield up from the right side, minding the upper left corner, which may catch on the metal framework.
-
If your iBook has Bluetooth, as discussed in the previous step, you will need to slide the antenna through the lower I-shaped hole in the shield before completely removing the shield.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 3 screws:
-
One 3 mm Phillips in the channel between the optical drive and fan.
-
One 6 mm Phillips from the upper end of the drive bezel.
-
One 6 mm Phillips with a collar from bracket extending from the lower left corner of the drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the orange optical drive ribbon from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
-
2) After disengaging the locking bar, slide the cable out of the connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Release the optical drive ribbon clamp as described above. Slide the optical drive ribbon out of its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the optical drive from the metal framework.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two Phillips screws securing the metal bracket and cable to the back of the optical drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel the cable up from the top of the optical drive, removing tape as necessary, and disconnect it.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single Phillips screw securing the bezel at the front of the optical drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to carefully depress the two tabs on top of the bezel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Hold the optical drive on its side and depress the remaining tab to free the bezel from the drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the drive over and remove the two Phillips screws from the bracket on the side of the drive.
-
Annulla: non ho completato questa guida.
Altre 24 persone hanno completato questa guida.