Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Usa una moneta per ruotare la vite di bloccaggio della batteria di 90 gradi in senso orario.
-
Solleva la batteria fuori dal computer.
-
-
-
Spingi nei cerchi sottili del coperchio inferiore che circondano lo scomparto della batteria, piegandoli oltre le alette, e poi solleva per liberare quell'angolo del case inferiore.
This part scared me, never in an iFixIt guide have I seen a warning like "trying times are ahead".
I used a plastic iPod opening tool and ran it around the seam in the same order pictured. I had the plastic off in less than a minute with almost no fuss.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free.
Citazione da Paulix:
I found it easier and "safer" to use a spudge at the back as well (two on each side of the hinge)
I did too. Thanks, Paulix.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the small greasy springs with white plastic caps from either side of the battery contacts.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 10 screws from the bottom shield:
-
Six 3 mm Phillips
-
Three 7.5 mm Phillips
-
One 14 mm Phillips
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single Phillips screw securing the DC-In board.
You might not need to remove the entire DC-In board and cable. This is removed because the DC-In jack blocks the upper case from being lifted off. I just removed the screw and pushed the board slightly in when removing the upper case to provide clearance. You may want to tape the board loosely in place when the screw is out to prevent it from falling out.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Angle the DC-In board out of its compartment.
Citazione da beefybov:
You need to undo the adhesive halfway down the cable, so you can lift the DC board to angle it out correctly. beefybov
Good call, beefybov.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the DC-In cable from the adhesive attaching it to the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the DC-In cable from the logic board.
-
Annulla: non ho completato questa guida.
Altre 63 persone hanno completato questa guida.
Documenti Allegati
4 Commenti
This was a really easy guide thanks. I had ordered a replacement DC in board but found after opening I could have probably repaired the existing one. It had been tripped over a few too many times. I think a bit of re-soldering on the connector where the tape covers in step 17 may have fixed mine. Now I have a backup at least.
Hi,
Does anyone happen to know the values of the L2 and L3 parts on this DC-in board?
I am looking to reuse them but I cannot find any specs.
Thank you and regards,
Vincent