Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Usa una moneta per ruotare di 90 gradi a sinistra entrambe le viti di fissaggio della batteria.
-
Rimuovi la cover della batteria.
-
Rimuovi la batteria dal computer sollevandola dalla linguetta di plastica.
-
-
-
Tirare verso di te le clip di sgancio della tastiera e solleva verso l'alto la tastiera fino a liberala. Nota che la tastiera è ancora collegata alla scheda logica da un cavo piatto, quindi non puoi rimuoverla completamente già ora.
-
Se la tastiera non si sgancia, usa un piccolo cacciavite a taglio per ruotare di 180° in qualsiasi direzione la vite di bloccaggio della tastiera (tra i pulsanti F4 e F5) e quindi prova di nuovo.
-
Ruota la tastiera, allontanandola così dallo schermo, e posala a faccia in giù sul trackpad.
-
-
-
Rimuovere le due viti a croce Phillips che fissano a schermatura della RAM.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a straightened paperclip to manually eject the CD-ROM tray.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the computer over so that the bottom is facing up.
-
Remove the following Torx screws:
-
Four short T8 Torx near the battery compartment.
-
Two long T8 Torx near the hinges.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the CD-ROM drive tray partly out.
-
Remove the silver Phillips screw from the plastic casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the computer over.
-
Remove the three Phillips screws.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
-
2) After disengaging the locking bar, slide the cable out of the connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Loosen the trackpad clamp by pulling the top piece up slightly, freeing the trackpad ribbon.
-
Slide the orange trackpad ribbon out of the clamp.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Push out the rim of the lower case and pull up on the upper case, grasping it just to the left of the optical drive.
-
Repeat the above step on the upper left corner of the upper case, grasping the bottom left corner of the upper case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the upper case on either side of the keyboard space and rotate up and away from the screen.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If the optical drive is not open, use a straightened paperclip to open it now.
-
Remove the 5 mm standoff.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the optical drive cable from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift up on the optical drive while sequentially pushing the small plastic tabs one after another toward the screen to free one side of the drive.
-
Lift up the side of the optical drive you just freed and slide the drive out and away from the screen.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following Phillips screws:
-
Remove the longer Phillips screw from the middle-rear of the modem shield.
-
Remove the three identical Phillips screws, two on either side of the EMI fingers, and the remaining one on the right side of the modem shield.
-
Remove the larger Phillips screw that secures the EMI fingers to the modem board.
-
Remove the EMI fingers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel the modem shield away from the metal framework below, working from the right front and moving to the left.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the Phillips screw from the left side of the modem.
-
Pry up the right side of the modem.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the modem partially out and disconnect the cable on the left side.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the Phillips screw from the left hinge.
-
Peel up the airport cable from beneath the yellow tape.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the large display data cable from the logic board and deroute it from the plastic and metal tabs.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the backlight cable from the logic board and deroute it.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three small Phillips screws from the clutch cover.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Finally, support the display with one hand while unscrewing the last Phillips screw from the right hinge (push the display gently down to avoid putting pressure on the screw).
-
Remove the display assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two small Phillips screws from the RJ-11 board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Push out the lower case rim and pull the RJ-11 board out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Deroute the speaker cable from the metal framework and disconnect it from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
There are six screws to remove (if you have an iBook without Firewire the screw circled in orange will not be present):
-
Two short, flat-headed Phillips screws near the battery compartment.
-
One short, round-headed Phillips near the speaker cable connector. (This is present on some models, but not others - especially the older ones)
-
One short, flat-headed Phillips between the ethernet and USB ports.
-
One short, flat-headed Phillips to the left of the hole-y (polite laughter) area.
-
One long, round-headed Phillips screw near the power receptacle.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the right side of the EMI shield up and pull it out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Push down firmly on the logic board and pull the DC-In board up from its connectors and then to the left.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three 5 mm standoffs securing the hard drive to the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the hard drive cable up from the logic board, using the plastic loop.
-
Lift the hard drive, with metal bracket attached, from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following screw and standoffs (the standoffs progress from smallest to largest):
-
One flat-headed Phillips screw near the left side of the RAM slot.
-
The smallest standoff, near where the left hinge used to be.
-
The slightly larger standoff, near where the right hinge used to be.
-
The even larger standoff, near the right side of the RAM slot.
-
The largest standoff, above where the optical drive used to be.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the charger board cable from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the logic board to the left of where the optical drive used to be and pull it up from the lower case.
-
Annulla: non ho completato questa guida.
Altre 8 persone hanno completato questa guida.
Documenti Allegati
2 Commenti
Hi, Can anyone tell me if there is a 3v battery on the logic board, like in an iMac? My iBook has not been used in years and starts up and dies before completion! Any ideas!
Thanks!
It's Soldered in so you might have to do some work to replace it
Chris -