Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Utilizza una moneta per ruotare la vite che blocca la batteria di 90 gradi in senso orario.
-
Estrai la batteria dal computer.
-
-
-
Tira le alette di rilascio della tastiera (evidenziate in rosso) verso di te e solleva la tastiera finché non viene fuori.
-
Se la tastiera non viene fuori, utilizza un piccolo cacciavite a taglio per ruotare la vite che blocca la tastiera di 180 gradi in qualsiasi direzione e riprova.
-
Capovolgi la tastiera, lontana dallo schermo, e posizionala a testa in giù sull'area del trackpad.
-
-
-
Utilizza uno spillo per rimuovere i tre piedini in gomma dal case inferiore.
-
-
-
-
Passa uno spudger lungo la linea di giunzione tra il case inferiore e il case superiore sulla parte anteriore del computer per liberare le alette che bloccano il case inferiore.
-
Tira su sul case inferiore e continua a utilizzare uno spudger finché necessario fino a sentire tre click distinti.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 9 screws on the bottom of the computer:
-
Three 3 mm Phillips around the battery compartment.
-
Three 5 mm Phillips on the left and bottom edges.
-
Three 14.5 mm Phillips on the top and right edges (you may have to peel back the foil tape to reveal the screw near the security lock slot).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn over the computer and open it.
-
Pry up the magnet covering a Phillips screw near the middle of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 3 screws on the edges of the keyboard area:
-
Two 6 mm Phillips underneath the keyboard area.
-
One 9 mm Phillips above the keyboard area.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
-
After disengaging the locking bar, slide the cable out of the connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Loosen the trackpad connector by pulling the top piece up slightly, freeing the trackpad ribbon.
-
Slide the orange trackpad ribbon out of the connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a straightened paperclip to open the optical drive tray, and pull it out about halfway.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the upper case from the left side and use your other hand to pull out the right side in order to clear the power receptacle.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the upper case enough to disconnect the blue and white power cable from the logic board.
-
Using your fingernails or a dental pick, carefully pry the connector from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the upper case off completely and disconnect the red and black speaker cable from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 16 screws:
-
Five 3 mm Phillips (these have smaller heads than the others).
-
Three 5 mm Phillips.
-
Eight 6 mm Phillips.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel back three strips of yellow tape in the bottom, left corner.
-
Peel back one strip of foil tape near the audio-out port, one near where the trackpad connects to the logic board, and one near where the screen latch used to be.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the top shield up from the right side, minding the upper left corner, which may catch on the metal framework.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
On the bottom of the computer, remove the two Phillips screws securing the optical drive to the metal framework.
-
Open the optical drive using a straightened paperclip (if it's not already opened).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using a small flathead screwdriver, pry up the small tab securing the faceplate to the optical drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pry up the white plastic tab on the other end of the drive. Pull the optical drive faceplate off, rotating it up and down slightly to get over the remaining two tabs.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the computer over and open the display.
-
Remove the three pieces of yellow tape securing the optical drive and inverter cable to the metal framework.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull out on the right edge of the metal casing and lift the edge of the optical drive up.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Free the inverter cable and Airport antenna cable from the corner of the optical drive and lift the drive up so that it stands vertical.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two Phillips screws and faceplate securing the large orange ribbon cable to the optical drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the orange ribbon cable from the optical drive.
-
Annulla: non ho completato questa guida.
Altre 3 persone hanno completato questa guida.