Salta al contenuto principale
Aiuto

iPad 2 CDMA Logic Board Replacement

Replace the Logic Board in your iPad 2 CDMA.

Use this guide to replace the logic board.

Passo 1 Logic Board  ¶ 

Carefully lay the LCD next to the rear panel. Use a plastic opening tool to lift the display data cable lock upwards. Pull the display data cable out of its socket.

Passo 1 Logic Board  ¶ 

  • Carefully lay the LCD next to the rear panel.

  • Use a plastic opening tool to lift the display data cable lock upwards.

  • Pull the display data cable out of its socket.

  • Do not pull the connector upward as you disconnect it from its socket.

Passo 2  ¶ 

Remove the LCD assembly from the rear panel assembly.

Passo 2  ¶ 

  • Remove the LCD assembly from the rear panel assembly.

Passo 3  ¶ 

Use a plastic opening tool to help remove the piece of tape covering the end of the dock connector cable. Use the edge of a plastic opening tool to carefully pry the dock connector cable's connector up from its socket on the logic board. Peel the dock connector ribbon cable off the rear panel.

Passo 3  ¶ 

  • Use a plastic opening tool to help remove the piece of tape covering the end of the dock connector cable.

  • Use the edge of a plastic opening tool to carefully pry the dock connector cable's connector up from its socket on the logic board.

  • Peel the dock connector ribbon cable off the rear panel.

Passo 4  ¶ 

Pry the speaker cable connector straight up from its socket on the logic board.

Passo 4  ¶ 

  • Pry the speaker cable connector straight up from its socket on the logic board.

Passo 5  ¶ 

Remove the two 2.1 mm Phillips screws securing the logic board bracket to the rear case near the digitizer cable socket. Remove the logic board bracket from the rear case.

Passo 5  ¶ 

  • Remove the two 2.1 mm Phillips screws securing the logic board bracket to the rear case near the digitizer cable socket.

  • Remove the logic board bracket from the rear case.

Passo 6  ¶ 

Use the edge of a plastic opening tool to flip up the retainer securing the control board cable connector to its socket on the logic board. Pull the connector away from its socket on the logic board. Do not lift the cable upward as you disconnect it.

Passo 6  ¶ 

  • Use the edge of a plastic opening tool to flip up the retainer securing the control board cable connector to its socket on the logic board.

  • Pull the connector away from its socket on the logic board.

  • Do not lift the cable upward as you disconnect it.

Passo 7  ¶ 

Remove the four 2.6 mm Phillips screws securing the logic and communications boards to the rear panel.

Passo 7  ¶ 

  • Remove the four 2.6 mm Phillips screws securing the logic and communications boards to the rear panel.

Passo 8  ¶ 

Use the edge of a plastic opening tool to gently pry the logic board up from the adhesive securing it to the rear case.

Passo 8  ¶ 

  • Use the edge of a plastic opening tool to gently pry the logic board up from the adhesive securing it to the rear case.

  • Do not lift the logic board too far off the back case. There are still antennas attached.

Passo 9  ¶ 

Slightly lift the top of the logic board and disconnect the two antennas on the left. Rotate the logic board towards the center of the iPad and disconnect the last antenna at the top of the logic board. Disconnect the Wi-Fi antenna at the bottom of the logic board.

Passo 9  ¶ 

  • Slightly lift the top of the logic board and disconnect the two antennas on the left.

  • Rotate the logic board towards the center of the iPad and disconnect the last antenna at the top of the logic board.

  • Disconnect the Wi-Fi antenna at the bottom of the logic board.

Passo 10  ¶ 

Remove the logic board from the iPad 2.

Passo 10  ¶ 

  • Remove the logic board from the iPad 2.