Salta al contenuto principale
Aiuto

MacBook Pro 15" Retina Display Mid 2015 Display Assembly Replacement

Replace the display assembly in your MacBook Pro 15" Retina Display Mid 2015.

Do you have a cracked screen or see weird vertical lines? Fear not! Use this guide to remove/replace the display assembly if something terrible has happened to the beautiful Retina display of your MacBook Pro.

Passo 1 Display Assembly  ¶ 

Use the tip of a spudger to flip up the display data cable lock and rotate it toward the MagSafe 2 power port side of the computer. Pull the display data cable straight out of its socket on the logic board. Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.

Passo 1 Display Assembly  ¶ 

  • Use the tip of a spudger to flip up the display data cable lock and rotate it toward the MagSafe 2 power port side of the computer.

  • Pull the display data cable straight out of its socket on the logic board.

  • Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.

  • Do not touch the contacts on the data connector or its socket with your fingers or any tools, as you may deposit oils or damage the pins.

Passo 2  ¶ 

Remove the two rubber hinge covers. Remove the two rubber hinge covers.

Passo 2  ¶ 

  • Remove the two rubber hinge covers.

Passo 3  ¶ 

Remove the two 3.2 mm T5 Torx screws securing the aluminum hinge covers to the upper case. Remove the two 3.2 mm T5 Torx screws securing the aluminum hinge covers to the upper case.

Passo 3  ¶ 

  • Remove the two 3.2 mm T5 Torx screws securing the aluminum hinge covers to the upper case.

Passo 4  ¶ 

Remove the two aluminum hinge covers from the MacBook Pro. Remove the two aluminum hinge covers from the MacBook Pro. Remove the two aluminum hinge covers from the MacBook Pro.

Passo 4  ¶ 

  • Remove the two aluminum hinge covers from the MacBook Pro.

Passo 5  ¶ 

Remove four out of the six 5.3 mm T8 Torx screws securing the display to the upper case. Leave the innermost screws (one from each hinge) in place.

Passo 5  ¶ 

  • Remove four out of the six 5.3 mm T8 Torx screws securing the display to the upper case.

  • Leave the innermost screws (one from each hinge) in place.

  • When reassembling, be sure the two screws going back into the hinge on the left go back through the webcam/AirPort cable bracket.

Passo 6  ¶ 

Open the MacBook Pro approximately 110 degrees, and place it sideways on the table, as shown.

Passo 6  ¶ 

  • Open the MacBook Pro approximately 110 degrees, and place it sideways on the table, as shown.

Passo 7  ¶ 

While holding the display and upper case together with your left hand, remove the remaining T8 Torx screw from the lower (closer to the table) display bracket.

Passo 7  ¶ 

  • While holding the display and upper case together with your left hand, remove the remaining T8 Torx screw from the lower (closer to the table) display bracket.

Passo 8  ¶ 

Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.

Passo 8  ¶ 

  • Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.

  • While holding the display and upper case together with your left hand, remove the remaining T8 Torx screw from the upper display bracket.

Passo 9  ¶ 

Grip both halves of the device, one in each hand. Gently push forward on the bottom half of the device to detach it from the display assembly. Carefully set each component aside, making sure to set down the bottom half keyboard-side down to avoid damaging internal components.

Passo 9  ¶ 

  • Grip both halves of the device, one in each hand.

  • Gently push forward on the bottom half of the device to detach it from the display assembly.

  • Carefully set each component aside, making sure to set down the bottom half keyboard-side down to avoid damaging internal components.

  • Replacement displays may not have their hinges adjusted to the correct angle. Use needle nose pliers to gently adjust them to match the hinges on the display being replaced.