Salta al contenuto principale
Aiuto

MacBook Core 2 Duo Optical Drive Replacement

Solo Prerequisita

Solo Prerequisita

Per favore tieni conto che questa guida è solo un prerequisito per altre guide.

  • Autore: iRobot
  • Difficoltà: Moderato

Access the combo or SuperDrive.

Sezioni

Passo 1 Optical Drive  ¶ 

Grasp the white plastic tab attached to the hard drive and pull it to the left, removing the hard drive from the computer.

Passo 1 Optical Drive  ¶ 

  • Grasp the white plastic tab attached to the hard drive and pull it to the left, removing the hard drive from the computer.

Passo 2  ¶ 

Remove the two Phillips screws from the front edge of the optical drive.

Passo 2  ¶ 

  • Remove the two Phillips screws from the front edge of the optical drive.

  • Two 3.25 mm Phillips #000, (Head: 4 mm. dia. x .3 mm thick)

Passo 3  ¶ 

Disconnect the orange optical drive ribbon cable from the logic board. This cable can also be disconnected by prying straight up using a spudger.

Passo 3  ¶ 

  • Disconnect the orange optical drive ribbon cable from the logic board. This cable can also be disconnected by prying straight up using a spudger.

Passo 4  ¶ 

Disconnect the newly revealed display data cable. If there is no pull-tab on the top of the connector, it may be helpful to use a spudger to disconnect this connector.

Passo 4  ¶ 

  • Disconnect the newly revealed display data cable. If there is no pull-tab on the top of the connector, it may be helpful to use a spudger to disconnect this connector.

Passo 5  ¶ 

Disconnect the (once again) newly-revealed hard drive cable.

Passo 5  ¶ 

  • Disconnect the (once again) newly-revealed hard drive cable.

Passo 6  ¶ 

Peel up the foil tape between the fan and the optical drive. Lift the foil tape from the fan side, leaving it attached to the optical drive.

Passo 6  ¶ 

  • Peel up the foil tape between the fan and the optical drive. Lift the foil tape from the fan side, leaving it attached to the optical drive.

  • During reassembly, be sure to route the cables beneath the tape before reattaching it.

Passo 7  ¶ 

Pull up the display data cable from along the edge of the optical drive to reveal a silver Phillips screw.

Passo 7  ¶ 

  • Pull up the display data cable from along the edge of the optical drive to reveal a silver Phillips screw.

Passo 8  ¶ 

Remove the 2 mm Phillips #00 screw securing the optical drive.

Passo 8  ¶ 

  • Remove the 2 mm Phillips #00 screw securing the optical drive.

  • The Bluetooth cable may be covering the screw. If so, carefully push it aside. You may need to unscrew the cable clip to free the cable enough.

Passo 9  ¶ 

Lift the Bluetooth antenna board from the right side of the optical drive.

Passo 9  ¶ 

  • Lift the Bluetooth antenna board from the right side of the optical drive.

Passo 10  ¶ 

Deroute the hard drive cable from along the front of the optical drive.

Passo 10  ¶ 

  • Deroute the hard drive cable from along the front of the optical drive.

Passo 11  ¶ 

Lift the front edge of the optical drive and slide it up and out of the computer.

Passo 11  ¶ 

  • Lift the front edge of the optical drive and slide it up and out of the computer.