Salta al contenuto principale
Aiuto

Motorola V3i Teardown

Smontaggio

Smontaggio

Gli smontaggi danno un'immagine dell'interno di device e non dovrebbero essere usati come istruzioni di smontaggio.

Guida con Contributo Membro

Guida con Contributo Membro

Uno straordinario membro della nostra comunità ha realizzato questa guida. Non è gestita dallo staff iFixit.

A Motorola V3i it's from the "RAZR" series.

The V3i had an improved camera resolution with 1,3Mpix and a external Memoryslot (MicroSD) for additional storage. Even if it had serveral problems with the keyboard and handling, it's one of the most sold mobilephones in the world.

Passo 1 Motorola V3i Teardown  ¶ 

A Motorola V3i!

Passo 1 Motorola V3i Teardown  ¶ 

  • A Motorola V3i!

  • Let's see what's inside...

Passo 2  ¶ 

Let's turn it and take out the battery. Remove these two screws.

Passo 2  ¶ 

  • Let's turn it and take out the battery.

  • Remove these two screws.

Passo 3  ¶ 

Now you can easily flip the cover.

Passo 3  ¶ 

  • Now you can easily flip the cover.

Passo 4  ¶ 

You need to detach these two plastic lashes from the surounding. Now you can remove this transparent plastic case. Now you can take out the speaker.

Passo 4  ¶ 

  • You need to detach these two plastic lashes from the surounding.

  • Now you can remove this transparent plastic case.

  • Now you can take out the speaker.

  • The metal thing on the end of the picture is the antenna.

Passo 5  ¶ 

So, that's the board. Vibra motor.

Passo 5  ¶ 

  • So, that's the board.

  • Vibra motor.

  • Mini USB.

  • Connector for the antenna.

  • After I took these EMI shields away it looks like this...

Passo 6  ¶ 

Bluetooth chip by Broadcom. 32Mbit PSRAM by STMicroelectronics.

Passo 6  ¶ 

  • Bluetooth chip by Broadcom.

  • 32Mbit PSRAM by STMicroelectronics.

  • Baseband Processor (Main Processor) by Freescale (90nm structure).

  • RF Transmitter by RF Micro Devices.

  • Battery controller by Freescale.

  • Quad-Band Transmit Module by RF Micro Devices.

Passo 7  ¶ 

Remove these 4 rubbers. Then remove the four torx screws.

Passo 7  ¶ 

  • Remove these 4 rubbers.

  • Then remove the four torx screws.

  • You can easily lose these rubbers. (That's why I have only 3 of them...)

Passo 8  ¶ 

Filp the device and you can remove the top housing. Remove the three buttons on the side of the device.

Passo 8  ¶ 

  • Filp the device and you can remove the top housing.

  • Remove the three buttons on the side of the device.

  • Remove the connector to the mainboard...

  • and to the camera.

Passo 9  ¶ 

Remove the camera by lifting it up.

Passo 9  ¶ 

  • Remove the camera by lifting it up.

  • That's a 1,3Mpix camera!

Passo 10  ¶ 

Lift up the speaker. Then, that's a tricky part,remove all the buttons around the screen housing. Caution: They are really thin and they easily break! After you did this tricky part you can lift the top of the phone away.

Passo 10  ¶ 

  • Lift up the speaker.

  • Then, that's a tricky part,remove all the buttons around the screen housing. Caution: They are really thin and they easily break!

  • After you did this tricky part you can lift the top of the phone away.

Passo 11  ¶ 

Now lift up the front glass from the top of the device. It's held with adhesives. After you did this it should look like this.

Passo 11  ¶ 

  • Now lift up the front glass from the top of the device. It's held with adhesives.

  • After you did this it should look like this.

Passo 12  ¶ 

Around the screen there are some lashes. Detach them to release the screen of the metal housing. Then you can lift the metal housing up.

Passo 12  ¶ 

  • Around the screen there are some lashes. Detach them to release the screen of the metal housing.

  • Then you can lift the metal housing up.

Passo 13  ¶ 

The metal housing is very fragile! an ATI Imageon chip! It's a mulitmedia co-processor, it is used for record video and mobile gaming. It support up to a 2Mpix camera.

Passo 13  ¶ 

  • The metal housing is very fragile!

  • an ATI Imageon chip! It's a mulitmedia co-processor, it is used for record video and mobile gaming. It support up to a 2Mpix camera.

Passo 14  ¶ 

Again there's a small lash on the botton of the front screen housing. After that you can remove the front screen with the PCB.

Passo 14  ¶ 

  • Again there's a small lash on the botton of the front screen housing.

  • After that you can remove the front screen with the PCB.

Passo 15  ¶ 

The front screen.

Passo 15  ¶ 

  • The front screen.

  • Yes, my front screen has some dead pixels. (They are pink?!)

Passo 16  ¶ 

Thank you for reading my Teardown:)

Passo 16  ¶ 

  • Thank you for reading my Teardown:)