Salta al contenuto principale
Aiuto

Black and Decker AS150 Steam Advantage Iron Teardown

Smontaggio

Smontaggio

Gli smontaggi danno un'immagine dell'interno di device e non dovrebbero essere usati come istruzioni di smontaggio.

In Lavorazione

In Lavorazione

Questa guida è un work in progress. Ricarica periodicamente per vedere le ultime modifiche!

This guide will show how to disassemble the Steam Advantage Iron.

Passo 1 Examine the Iron  ¶ 

Note that the base of the iron is detached from the upper portion where the dials and handle are location. Note that the base of the iron is detached from the upper portion where the dials and handle are location. Note that the base of the iron is detached from the upper portion where the dials and handle are location.

Passo 1 Examine the Iron  ¶ 

  • Note that the base of the iron is detached from the upper portion where the dials and handle are location.

Passo 2 Remove all visible screws  ¶ 

First remove all the large screws that detach the silver hot plate from the plastic piece attached to it. Lift the white plastic piece to reveal the inner workings of the iron (see last photo attached) First remove all the large screws that detach the silver hot plate from the plastic piece attached to it. Lift the white plastic piece to reveal the inner workings of the iron (see last photo attached) First remove all the large screws that detach the silver hot plate from the plastic piece attached to it. Lift the white plastic piece to reveal the inner workings of the iron (see last photo attached)

Passo 2 Remove all visible screws  ¶ 

  • First remove all the large screws that detach the silver hot plate from the plastic piece attached to it. Lift the white plastic piece to reveal the inner workings of the iron (see last photo attached)

Passo 3 Clear dust off  ¶ 

This iron was particularly dusty, clear the dust away with a toothbrush or other small brush. The result is shown in the photo; a clean, dust free iron.

Passo 3 Clear dust off  ¶ 

  • This iron was particularly dusty, clear the dust away with a toothbrush or other small brush. The result is shown in the photo; a clean, dust free iron.

Passo 4 Further Remove Screws  ¶ 

Remove the smaller screws located near the square(back) end of the iron releasing cords and wires. Also remove little orange rubber gaskets, and white plastic spacers, taking note where everything was. At this point, your iron should be completely disassembled, and should look like the last photo attached. Remove the smaller screws located near the square(back) end of the iron releasing cords and wires. Also remove little orange rubber gaskets, and white plastic spacers, taking note where everything was. At this point, your iron should be completely disassembled, and should look like the last photo attached.

Passo 4 Further Remove Screws  ¶ 

  • Remove the smaller screws located near the square(back) end of the iron releasing cords and wires. Also remove little orange rubber gaskets, and white plastic spacers, taking note where everything was. At this point, your iron should be completely disassembled, and should look like the last photo attached.

Passo 5 Re-assemble  ¶ 

Beginning with the spacers and gaskets, replace these parts where they belong. Then re-install the small internal screws, taking care to reattach the wires and cords with them. Close the white plastic plate onto the metal hot plate and re-attach the larger main screws. Place black dial receptacle into orange slot (as pictured). Beginning with the spacers and gaskets, replace these parts where they belong. Then re-install the small internal screws, taking care to reattach the wires and cords with them. Close the white plastic plate onto the metal hot plate and re-attach the larger main screws. Place black dial receptacle into orange slot (as pictured). Beginning with the spacers and gaskets, replace these parts where they belong. Then re-install the small internal screws, taking care to reattach the wires and cords with them. Close the white plastic plate onto the metal hot plate and re-attach the larger main screws. Place black dial receptacle into orange slot (as pictured).

Passo 5 Re-assemble  ¶ 

  • Beginning with the spacers and gaskets, replace these parts where they belong. Then re-install the small internal screws, taking care to reattach the wires and cords with them. Close the white plastic plate onto the metal hot plate and re-attach the larger main screws. Place black dial receptacle into orange slot (as pictured).