Salta al contenuto principale
Aiuto

iPod Touch 3rd Generation Display Replacement

Guida In Evidenza

Guida In Evidenza

Questa guida è stata giudicata eccezionalmente ben fatta dallo staff iFixit.

Replace a broken LCD.

  • Autore: Andrew Bookholt
  • Stima il tempo: 10 - 20 minuti
  • Difficoltà: Difficile

Use this guide to replace a broken display on the iPod Touch 3rd Generation.

Passo 1 Display  ¶ 

Insert a small iPod opening tool with the edge angled up toward the underside of the display between the white plastic backlight and the metal shield beneath it.

Passo 1 Display  ¶ 

  • Insert a small iPod opening tool with the edge angled up toward the underside of the display between the white plastic backlight and the metal shield beneath it.

  • Pry up along the lower edge of the display enough to grab it with your fingers, being careful to not flex the screen.

Passo 2  ¶ 

Lift the display up from its lower edge and rotate it toward the top of the Touch.

Passo 2  ¶ 

  • Lift the display up from its lower edge and rotate it toward the top of the Touch.

  • The next few steps require removal of components under where the display normally sits. Be sure to hold the display to avoid putting tension on the delicate display ribbon cable.

  • Remove the seven Phillips screws securing the metal display tray to the rear panel. They may be very tight; watch carefully to make sure you don't strip them.

  • The two darker screws belong in the two holes in the tray nearest the bottom edge of the Touch.

Passo 3  ¶ 

Lay the display back down into its tray.

Passo 3  ¶ 

  • Lay the display back down into its tray.

  • Remove the final Phillips screw securing the metal tray to the rear panel.

Passo 4  ¶ 

Lift the display out of the metal tray and rotate it toward the top edge of the Touch.

Passo 4  ¶ 

  • Lift the display out of the metal tray and rotate it toward the top edge of the Touch.

  • Use an iPod opening tool to lift the metal display tray and rotate it up toward the top edge of the Touch.

Passo 5  ¶ 

Use the edge of an iPod opening tool to peel the copper tape off the top edge of the display.

Passo 5  ¶ 

  • Use the edge of an iPod opening tool to peel the copper tape off the top edge of the display.

  • Leave the copper tape attached to the metal display tray.

Passo 6  ¶ 

Use the edge of an iPod opening tool to remove the piece of tape covering the display data cable.

Passo 6  ¶ 

  • Use the edge of an iPod opening tool to remove the piece of tape covering the display data cable.

Passo 7  ¶ 

Use an iPod opening tool to pry the display data cable connector up off its socket on the logic board.

Passo 7  ¶ 

  • Use an iPod opening tool to pry the display data cable connector up off its socket on the logic board.

Passo 8  ¶ 

Peel the display data cable off the adhesive securing it to the rear panel.

Passo 8  ¶ 

  • Peel the display data cable off the adhesive securing it to the rear panel.

Passo 9  ¶ 

Lift the metal display tray slightly (the battery is attached to its underside) and remove the display from the Touch, minding its delicate cable that may get caught.

Passo 9  ¶ 

  • Lift the metal display tray slightly (the battery is attached to its underside) and remove the display from the Touch, minding its delicate cable that may get caught.

  • The display ribbon cable is routed under the metal display tray.