Salta al contenuto principale
Aiuto

Razer Blade 14 (2013) Teardown

Smontaggio

Smontaggio

Gli smontaggi danno un'immagine dell'interno di device e non dovrebbero essere usati come istruzioni di smontaggio.

Guida con Contributo Membro

Guida con Contributo Membro

Uno straordinario membro della nostra comunità ha realizzato questa guida. Non è gestita dallo staff iFixit.

This is my tear down of the Razer Blade 14. I haven't yet seen anyone dismantle this notebook so i decided to give it as try and went as far as I felt comfortable going.

Passo 1 Razer Blade 14 (2013) Teardown  ¶ 

The thin and sleek gaming Notebook from Razer. The thin and sleek gaming Notebook from Razer.

Passo 1 Razer Blade 14 (2013) Teardown  ¶ 

  • The thin and sleek gaming Notebook from Razer.

Passo 2  ¶ 

Remove the 10 Screws holding the back Cover on to reveal the mainboard. DDR3 Ram chips CPU Chipset

Passo 2  ¶ 

  • Remove the 10 Screws holding the back Cover on to reveal the mainboard.

  • DDR3 Ram chips

  • CPU Chipset

  • Liteon 256gb SSD (factory installed)

  • Factory WLAN/BT card

  • Battery

  • Aftermarket MSata SSD (installation screw not included)

Passo 3  ¶ 

Removing the Battery Removing the Battery Removing the Battery

Passo 3  ¶ 

  • Removing the Battery

Passo 4  ¶ 

Apparently this notebook was named even before i got it! In my use this battery will last through 4-5 hours of movies on power saver mode. Apparently this notebook was named even before i got it! In my use this battery will last through 4-5 hours of movies on power saver mode. Apparently this notebook was named even before i got it! In my use this battery will last through 4-5 hours of movies on power saver mode.

Passo 4  ¶ 

  • Apparently this notebook was named even before i got it! In my use this battery will last through 4-5 hours of movies on power saver mode.

Passo 5  ¶ 

Removing the Speakers. Removing the Speakers.

Passo 5  ¶ 

  • Removing the Speakers.

Passo 6  ¶ 

The original mSATA SSD. (the secondary seen earlier was added by myself. The original mSATA SSD. (the secondary seen earlier was added by myself. The original mSATA SSD. (the secondary seen earlier was added by myself.

Passo 6  ¶ 

  • The original mSATA SSD. (the secondary seen earlier was added by myself.

Passo 7  ¶ 

Removing the fans. Removing the fans. Removing the fans.

Passo 7  ¶ 

  • Removing the fans.

Passo 8  ¶ 

Removing the heatsinks. Removing the heatsinks. Removing the heatsinks.

Passo 8  ¶ 

  • Removing the heatsinks.

Passo 9  ¶ 

Removing the mainboard. Removing the mainboard. Removing the mainboard.

Passo 9  ¶ 

  • Removing the mainboard.

Passo 10  ¶ 

This is the end of the teardown. anything past this point would likely cause damage to the notebook and as i intend to continue using it, this would be undesirable. Just one thing i noticed, that there is an debug ribbon cable plug left on the board, another thing, the power plug is replaceable. This is the end of the teardown. anything past this point would likely cause damage to the notebook and as i intend to continue using it, this would be undesirable. Just one thing i noticed, that there is an debug ribbon cable plug left on the board, another thing, the power plug is replaceable. This is the end of the teardown. anything past this point would likely cause damage to the notebook and as i intend to continue using it, this would be undesirable. Just one thing i noticed, that there is an debug ribbon cable plug left on the board, another thing, the power plug is replaceable.

Passo 10  ¶ 

  • This is the end of the teardown. anything past this point would likely cause damage to the notebook and as i intend to continue using it, this would be undesirable. Just one thing i noticed, that there is an debug ribbon cable plug left on the board, another thing, the power plug is replaceable.