Salta al contenuto principale
Aiuto

Conair Cord-Keeper 169XR Dryer Head Disassembly

Foto Azione

Foto Azione

Passa all'azione, eroe! Questa guida ha bisogno di immagini che meglio illustrano come eseguire azioni specifiche.

This is a prerequisite guide to prepare you for the Retracting Button Replacement, Retracting Mechanism Replacement, and the Fan Grill Replacement.

  • Autore: Candace
  • Stima il tempo: 15 - 20 minuti
  • Difficoltà: Moderato

You are going to be starting from the handle and working your way to the head of the dryer in this disassembly.

Sezioni
Strumenti

Passo 1 Dryer Head  ¶ 

Remove the inner white disk piece by gently pulling it out with your finger nail. Remove the inner white disk piece by gently pulling it out with your finger nail.

Passo 1 Dryer Head  ¶ 

  • Remove the inner white disk piece by gently pulling it out with your finger nail.

Passo 2  ¶ 

Gently remove the tan boxes (power supply) by wiggling them out of place and set them aside so you can take the back part of the handle off. Gently remove the tan boxes (power supply) by wiggling them out of place and set them aside so you can take the back part of the handle off. Gently remove the tan boxes (power supply) by wiggling them out of place and set them aside so you can take the back part of the handle off.

Passo 2  ¶ 

  • Gently remove the tan boxes (power supply) by wiggling them out of place and set them aside so you can take the back part of the handle off.

Passo 3  ¶ 

Remove the inner white disk piece from the base of the dryer head by gently pulling it out with your finger nail. Remove the inner white disk piece from the base of the dryer head by gently pulling it out with your finger nail.

Passo 3  ¶ 

  • Remove the inner white disk piece from the base of the dryer head by gently pulling it out with your finger nail.

Passo 4  ¶ 

Unscrew the three 12 mm long Phillips #2 screws to remove the back of the hairdryer.

Passo 4  ¶ 

  • Unscrew the three 12 mm long Phillips #2 screws to remove the back of the hairdryer.

Passo 5  ¶ 

Once the three screws are removed, pop the back of the dryer off by wiggling it until it comes loose.  This shouldn't take too much effort.

Passo 5  ¶ 

  • Once the three screws are removed, pop the back of the dryer off by wiggling it until it comes loose. This shouldn't take too much effort.

Passo 6  ¶ 

At this point, unwind the cord and lay it to the side so you can get to the screw in the middle easier. Remove the single 12 mm long Phillips #2 screw in the middle of the cord track.

Passo 6  ¶ 

  • At this point, unwind the cord and lay it to the side so you can get to the screw in the middle easier.

  • Remove the single 12 mm long Phillips #2 screw in the middle of the cord track.

Passo 7  ¶ 

Take off the white cap that covers the heating coil.  You will see a wound up piece of metal (cord retracting coil) underneath once the cap is removed. Take off the white cap that covers the heating coil.  You will see a wound up piece of metal (cord retracting coil) underneath once the cap is removed.

Passo 7  ¶ 

  • Take off the white cap that covers the heating coil. You will see a wound up piece of metal (cord retracting coil) underneath once the cap is removed.

Passo 8  ¶ 

When removing the coil, make sure it stays wound up.  It could very easily pop out, and you would have to wind it all the way back up and try to squeeze it back into the slot when you reassemble the dryer. To remove the coil, use your screw driver to pop the coil out of the slot.

Passo 8  ¶ 

  • When removing the coil, make sure it stays wound up. It could very easily pop out, and you would have to wind it all the way back up and try to squeeze it back into the slot when you reassemble the dryer.

  • To remove the coil, use your screw driver to pop the coil out of the slot.

  • This is what the coil would look like if it came undone when you removed it.

Passo 9  ¶ 

Once the coil is removed, unscrew the three 11 mm long Phillips #2 screws underneath to remove the retracting wheel. Once the coil is removed, unscrew the three 11 mm long Phillips #2 screws underneath to remove the retracting wheel. Once the coil is removed, unscrew the three 11 mm long Phillips #2 screws underneath to remove the retracting wheel.

Passo 9  ¶ 

  • Once the coil is removed, unscrew the three 11 mm long Phillips #2 screws underneath to remove the retracting wheel.