Salta al contenuto principale
Aiuto

Zune Flash 2nd Generation Face Plate Replacement

Immagini Non Adeguate

Immagini Non Adeguate

Aggiornare le immagini per renderle più in sintonia con le prerequisite aumenterebbe l'attrattiva di questa guida.

Necessarie Immagini Migliori

Necessarie Immagini Migliori

Delle foto più belle renderanno migliore questa guida. Contribuisci scattando, modificando o caricando immagini nuove!

  • Autore: ybahman
  • Stima il tempo: 5 - 10 minuti
  • Difficoltà: Moderato

This guide shows you how to replace the Zune Flash 2nd Generation face plate.

Passo 1 Face Plate  ¶ 

Remove the three screws (5.5mm by 3mm) from the backside of the Zune using a small Tri-Wing screwdriver. Be sure to put this set of screws aside since they are a different size than any other screws in the device.

Passo 1 Face Plate  ¶ 

  • Remove the three screws (5.5mm by 3mm) from the backside of the Zune using a small Tri-Wing screwdriver.

  • Be sure to put this set of screws aside since they are a different size than any other screws in the device.

Passo 2  ¶ 

Use your finger or a Zune opening tool to pry back the two clear flaps. Next lift the communications board that was being held down by the clear flaps.

Passo 2  ¶ 

  • Use your finger or a Zune opening tool to pry back the two clear flaps.

  • Next lift the communications board that was being held down by the clear flaps.

  • Be careful not to accidentally detach the slim ribbon that connects between the communications board and the device.

Passo 3  ¶ 

Disconnect the ribbon with the plastic opening tool by flipping up the black plastic flap where the ribbon connects to the memory board. Carefully pull the ribbon out of the memory board, ensuring that the black plastic flap is up before removal to avoid the ripping the ribbon. Carefully pull the ribbon out of the memory board, ensuring that the black plastic flap is up before removal to avoid the ripping the ribbon.

Passo 3  ¶ 

  • Disconnect the ribbon with the plastic opening tool by flipping up the black plastic flap where the ribbon connects to the memory board.

  • Carefully pull the ribbon out of the memory board, ensuring that the black plastic flap is up before removal to avoid the ripping the ribbon.

Passo 4  ¶ 

Remove the battery by prying the battery off from the bottom with a Zune opening tool. There is an adhesive between the battery and the device, therefore use a metal spudger to finish detaching the battery. Be sure not to puncture the battery in any way when using the metal spudger.

Passo 4  ¶ 

  • Remove the battery by prying the battery off from the bottom with a Zune opening tool.

  • There is an adhesive between the battery and the device, therefore use a metal spudger to finish detaching the battery.

  • Be sure not to puncture the battery in any way when using the metal spudger.

Passo 5  ¶ 

Remove the single screw under the battery using a small Tri-Wing screwdriver. Remove the single screw under the battery using a small Tri-Wing screwdriver.

Passo 5  ¶ 

  • Remove the single screw under the battery using a small Tri-Wing screwdriver.

Passo 6  ¶ 

Disconnect the faceplate from the device by depressing the two tabs located near the middle of each of the sides using a metal spudger.

Passo 6  ¶ 

  • Disconnect the faceplate from the device by depressing the two tabs located near the middle of each of the sides using a metal spudger.

  • This will disconnect the last circuit board in the device from the center frame.

Passo 7  ¶ 

Remove the faceplate by using a metal spudger to separate it from the remaining components. Remove the faceplate by using a metal spudger to separate it from the remaining components. Remove the faceplate by using a metal spudger to separate it from the remaining components.

Passo 7  ¶ 

  • Remove the faceplate by using a metal spudger to separate it from the remaining components.