Salta al contenuto principale
Aiuto

HTC myTouch 3G Motherboard Replacement

Vigilanza sulla Grammatica

Vigilanza sulla Grammatica

Adotta il tuo insegnante di inglese interno e contribuisci a migliorare la grammatica di questa guida!

Testo Confuso

Testo Confuso

Parte del testo di questa guida è confusionario, doppio, o fuori tema. Modificarlo per renderlo più chiaro!

Attrezzi Non Corretti

Attrezzi Non Corretti

Contribuisci a rendere migliore questa guida usando i giusti strumenti nelle immagini e/o nel testo.

Fallo a Fettine

Fallo a Fettine

I passaggi in questa guida dovrebbero essere suddivisi e trasformati in una serie di guide prerequisite.

Replace the motherboard of your HTC myTouch 3G.

  • Autore: Tony Tran
  • Stima il tempo: 30 - 45 minuti
  • Difficoltà: Moderato

This guide describes the steps to separate the HTC myTouch motherboard from the glass screen for replacement or repair. This guide will require you to unscrew a T5 Torx screw with a VOID label. Unfastening this screw would void any warranty the phone may have.

Passo 1 Motherboard  ¶ 

Press each thumb on both sides of the upper corners and apply pressure downwards. Then, while still applying pressure, slide the back cover down.

Passo 1 Motherboard  ¶ 

  • Press each thumb on both sides of the upper corners and apply pressure downwards.

  • Then, while still applying pressure, slide the back cover down.

Passo 2  ¶ 

Remove the Battery. Remove the SIM card.

Passo 2  ¶ 

  • Remove the Battery.

  • Remove the SIM card.

Passo 3  ¶ 

Push the SD card in and the SD card should pop loose.

Passo 3  ¶ 

  • Push the SD card in and the SD card should pop loose.

  • Pull the SD card out.

Passo 4  ¶ 

Remove the four 6-mm T5 torx screws in the four corners. Remove the two 4-mm T5 torx screws in the middle.

Passo 4  ¶ 

  • Remove the four 6-mm T5 torx screws in the four corners.

  • Remove the two 4-mm T5 torx screws in the middle.

Passo 5  ¶ 

Use the existing gap, to dislodge the antenna cover from the phone. Pull out the antenna cover to have access to the motherboard.

Passo 5  ¶ 

  • Use the existing gap, to dislodge the antenna cover from the phone.

  • Pull out the antenna cover to have access to the motherboard.

Passo 6  ¶ 

Use a precision flathead screwdriver to dislodge the back plate from the phone by carefully inserting it into the slit between the frame and cover and pushing downward. Go around the edges of the phone, and continue to dislodge the back plate from the front part of the phone.

Passo 6  ¶ 

  • Use a precision flathead screwdriver to dislodge the back plate from the phone by carefully inserting it into the slit between the frame and cover and pushing downward.

  • Go around the edges of the phone, and continue to dislodge the back plate from the front part of the phone.

Passo 7  ¶ 

Remove the 3-mm Phillips head screw located on the side of the bottom left-hand corner of the phone. Remove the 3-mm Phillips head screw located on the top right-hand corner of the phone.

Passo 7  ¶ 

  • Remove the 3-mm Phillips head screw located on the side of the bottom left-hand corner of the phone.

  • Remove the 3-mm Phillips head screw located on the top right-hand corner of the phone.

  • Do not remove any of the screws located on the actual circuit boards.

Passo 8  ¶ 

Place a finger between the circuit board and the front cover, and lift up gently. Continue separating the circuit board from the front cover and screen and watch for a ribbon cable to detach. Finish separating the circuit board from the front panel.

Passo 8  ¶ 

  • Place a finger between the circuit board and the front cover, and lift up gently.

  • Continue separating the circuit board from the front cover and screen and watch for a ribbon cable to detach.

  • Finish separating the circuit board from the front panel.