Salta al contenuto principale
Aiuto

2003-2007 Honda Accord Oil and Oil Filter Change

Passo Mancante

Passo Mancante

Oops! A questa guida al momento mancano alcuni passi importanti.

Instructions for replacing the oil and oil filter in a 2003-2007 Honda Accord.

  • Autore: Shaun MacDonald
  • Stima il tempo: 20 - 30 minuti
  • Difficoltà: Moderato

It is suggested that you change your engine oil and filter every 5000 miles.

Sezioni
Strumenti

Passo 1 Engine oil and oil filter  ¶ 

Remove the dipstick by lifting vertically. Wipe all the oil off of the dipstick and put it back into the dipstick port.

Passo 1 Engine oil and oil filter  ¶ 

  • Remove the dipstick by lifting vertically.

  • Wipe all the oil off of the dipstick and put it back into the dipstick port.

Passo 2  ¶ 

Remove the dipstick and examine the oil levels. The oil level should be between the two dots on the dipstick.

Passo 2  ¶ 

  • Remove the dipstick and examine the oil levels. The oil level should be between the two dots on the dipstick.

Passo 3  ¶ 

Locate the oil fill cap on top of the engine and unscrew it.

Passo 3  ¶ 

  • Locate the oil fill cap on top of the engine and unscrew it.

Passo 4  ¶ 

After driving, engine oil needs time to cool before it can be safely changed. Wait about one hour after the engine has been turned off before attempting to change the oil. Crawl under the front of the car on your backside and identify the oil drain plug.

Passo 4  ¶ 

  • After driving, engine oil needs time to cool before it can be safely changed. Wait about one hour after the engine has been turned off before attempting to change the oil.

  • Crawl under the front of the car on your backside and identify the oil drain plug.

  • If there is any oil or residue around the drain plug, be sure to wipe it off before continuing.

Passo 5  ¶ 

Place the oil drip pan under the drain plug and begin to loosen the drain plug with a 17mm wrench.

Passo 5  ¶ 

  • Place the oil drip pan under the drain plug and begin to loosen the drain plug with a 17mm wrench.

Passo 6  ¶ 

Loosen drain plug slowly by hand until the bolt is completely removed and oil begins to flow, re-positioning the oil drip pan if needed. Loosen drain plug slowly by hand until the bolt is completely removed and oil begins to flow, re-positioning the oil drip pan if needed.

Passo 6  ¶ 

  • Loosen drain plug slowly by hand until the bolt is completely removed and oil begins to flow, re-positioning the oil drip pan if needed.

Passo 7  ¶ 

Let the oil completely drain into the drip pan.

Passo 7  ¶ 

  • Let the oil completely drain into the drip pan.

  • Put a new crush washer on the drain bolt, then reinstall the drain bolt.

  • Using a torque wrench, tighten it to:

  • 33 lbf·ft (45 N·m , 4.6 kgf·m) for 4-cylinder models

  • or 29 lbf·ft (39 N·m , 4.0 kgf·m) for 6-cylinder models.

  • Set the drip pan aside.

Passo 8  ¶ 

Identify the oil filter and place drip pan under the oil filter to catch falling oil. Using a pair of channel locks, grip the oil filter tightly and twist counterclockwise to loosen. Oil will drip out from the threads as you loosen it so have the oil drip pan ready.

Passo 8  ¶ 

  • Identify the oil filter and place drip pan under the oil filter to catch falling oil.

  • Using a pair of channel locks, grip the oil filter tightly and twist counterclockwise to loosen.

  • Oil will drip out from the threads as you loosen it so have the oil drip pan ready.

Passo 9  ¶ 

Slowly loosen the oil filter by hand until it is free. Slowly loosen the oil filter by hand until it is free. Slowly loosen the oil filter by hand until it is free.

Passo 9  ¶ 

  • Slowly loosen the oil filter by hand until it is free.

Passo 10  ¶ 

Drain the remaining oil in the filter by inverting it over the drip pan. Be sure to wipe down any oil that might have leaked during the process.

Passo 10  ¶ 

  • Drain the remaining oil in the filter by inverting it over the drip pan.

  • Be sure to wipe down any oil that might have leaked during the process.

Passo 11  ¶ 

Get the replacement filter and lightly spread clean engine oil onto the rubber gasket of the new filter. Get the replacement filter and lightly spread clean engine oil onto the rubber gasket of the new filter.

Passo 11  ¶ 

  • Get the replacement filter and lightly spread clean engine oil onto the rubber gasket of the new filter.

Passo 12  ¶ 

Thread the new filter into the oil filter port by turning the filter clockwise.

Passo 12  ¶ 

  • Thread the new filter into the oil filter port by turning the filter clockwise.

  • Once the rubber gasket contacts the engine block, use the channel locks to turn the filter one full turn CW.

  • Over tightening may cause the gasket to break and leak oil.

Passo 13  ¶ 

Using a funnel, pour 5 quarts of 5W-20 oil into the opening, making sure not to spill oil onto or around the engine.

Passo 13  ¶ 

  • Using a funnel, pour 5 quarts of 5W-20 oil into the opening, making sure not to spill oil onto or around the engine.

  • Screw on and tighten the oil fill cap.