Salta al contenuto principale
Aiuto

Asus Zenbook UX21e LCD Screen Replacement

Guida Studente in Evidenza

Guida Studente in Evidenza

Questa guida è frutto del duro lavoro dei nostri bravissimi studenti e il nostro staff iFixit la trova eccezionalmente brillante.

This guide will enable you to replace the LCD screen for your Asus Zenbook UX21e.

  • Autore: Zachary Eslick
  • Stima il tempo: 45 minuti - 1 ora
  • Difficoltà: Difficile

For the LCD screen, initially, follow the battery replacement guide, then disconnect the LCD connector from the motherboard. Separate the screen by unscrewing the hinges and pulling the screen from the device. From there you must open up the screen by removing a vent, bezel, and rubber o-ring. Finally, you disconnect three cables and unscrew the screen to complete the guide.

Sezioni
Strumenti

Passo 1 LCD Screen  ¶ 

Remove the tape wrapped around the LCD connector by pulling it towards the screen hinges of the computer. Disconnect the LCD connector by sliding it out of its socket. Disconnect the LCD connector by sliding it out of its socket.

Passo 1 LCD Screen  ¶ 

  • Remove the tape wrapped around the LCD connector by pulling it towards the screen hinges of the computer.

  • Disconnect the LCD connector by sliding it out of its socket.

Passo 2  ¶ 

Using a Phillis #1 screwdriver, remove the four 3 mm screws at the screen hinges to allow the screen to pull off of the device. If the hinges are too hard to remove by hand, use the leverage of the keyboard to slide them out. If the hinges are too hard to remove by hand, use the leverage of the keyboard to slide them out.

Passo 2  ¶ 

  • Using a Phillis #1 screwdriver, remove the four 3 mm screws at the screen hinges to allow the screen to pull off of the device.

  • If the hinges are too hard to remove by hand, use the leverage of the keyboard to slide them out.

Passo 3  ¶ 

Remove the plastic vent from screen by using an iFixit opening tool to pry the vent from the screen edge. Exercise caution when prying the vent off. Too much deflection can cause the vent to snap. Work both ends.

Passo 3  ¶ 

  • Remove the plastic vent from screen by using an iFixit opening tool to pry the vent from the screen edge.

  • Exercise caution when prying the vent off. Too much deflection can cause the vent to snap. Work both ends.

Passo 4  ¶ 

Remove the nine 3 mm screws along the base of the screen using a Phillips #1 screwdriver. Remove four 5 mm screws along the two internal hinges using a Phillips #1 screwdriver. These four screws are hidden by cables and need to be removed in order to see the screws.

Passo 4  ¶ 

  • Remove the nine 3 mm screws along the base of the screen using a Phillips #1 screwdriver.

  • Remove four 5 mm screws along the two internal hinges using a Phillips #1 screwdriver.

  • These four screws are hidden by cables and need to be removed in order to see the screws.

Passo 5  ¶ 

Remove the rubber o-ring (the thin rubber strip that lines the bezel edge)  by peeling it off. Heat the bezel using any heating tool such as a hair dryer, etc. Use a metal spudger to help rip off the bezel and the rubber-o-ring.

Passo 5  ¶ 

  • Remove the rubber o-ring (the thin rubber strip that lines the bezel edge) by peeling it off.

  • Heat the bezel using any heating tool such as a hair dryer, etc.

  • Use a metal spudger to help rip off the bezel and the rubber-o-ring.

Passo 6  ¶ 

Disconnect the LCD connector from the screen housing by pulling the connector. Disconnect the LCD connector from the screen housing by pulling the connector.

Passo 6  ¶ 

  • Disconnect the LCD connector from the screen housing by pulling the connector.

Passo 7  ¶ 

Unscrew the two 2 mmm screws that line the screen control board using a Phillips #1 screwdriver. Unscrew the two 2 mmm screws that line the screen control board using a Phillips #1 screwdriver.

Passo 7  ¶ 

  • Unscrew the two 2 mmm screws that line the screen control board using a Phillips #1 screwdriver.

Passo 8  ¶ 

Remove the cable connecting the screen housing to the control board by pulling the cable. Remove the cable connecting the screen housing to the control board by pulling the cable. Remove the cable connecting the screen housing to the control board by pulling the cable.

Passo 8  ¶ 

  • Remove the cable connecting the screen housing to the control board by pulling the cable.