Salta al contenuto principale
Aiuto

Pioneer Elite PRO-RO6U Motherboard Replacement

Necessarie Immagini Migliori

Necessarie Immagini Migliori

Delle foto più belle renderanno migliore questa guida. Contribuisci scattando, modificando o caricando immagini nuove!

Replacement of the Pioneer Elite Pro-R06U motherboard.

  • Autore: Cody Carter
  • Stima il tempo: 30 - 45 minuti
  • Difficoltà: Moderato

Replacing the motherboard of the Pioneer Elite Pro-R06U may be necessary if the receiver is dropped or takes water damage. This part is the trickiest to replace as it is located beneath all other components of the receiver.

Passo 1 Motherboard  ¶ 

To remove the optical drive cooling fan, grip the ribbon connector at M11 and gently remove by pulling away for the slot.

Passo 1 Motherboard  ¶ 

  • To remove the optical drive cooling fan, grip the ribbon connector at M11 and gently remove by pulling away for the slot.

Passo 2  ¶ 

Flip the latch on the ribbon connector upward to allow for cable removal.

Passo 2  ¶ 

  • Flip the latch on the ribbon connector upward to allow for cable removal.

  • Grip the ribbon cable and remove by gently pulling away from the unlatched connector.

Passo 3  ¶ 

Remove the two 6.4 mm Phillips mounting screws on the optical drive cooling fan.

Passo 3  ¶ 

  • Remove the two 6.4 mm Phillips mounting screws on the optical drive cooling fan.

Passo 4  ¶ 

Grip the frame of the cooling fan and slide it toward the front panel, then lift out of the device.

Passo 4  ¶ 

  • Grip the frame of the cooling fan and slide it toward the front panel, then lift out of the device.

Passo 5  ¶ 

Unplug ribbon cables D4 and D5. To unplug D4, flip the gate up and pull the ribbon away.

Passo 5  ¶ 

  • Unplug ribbon cables D4 and D5. To unplug D4, flip the gate up and pull the ribbon away.

Passo 6  ¶ 

Remove four 1/4th inch Phillips screws on the back of the casing.

Passo 6  ¶ 

  • Remove four 1/4th inch Phillips screws on the back of the casing.

  • Unscrew and remove the nut from the threaded connector.

Passo 7  ¶ 

The optical drive is still connected by a cable on its bottom side, lift the drive upwards only slightly when first removing from the casing. Pull the optical drive toward the interior of the device and then lift upwards, then pull to remove the cord on the bottom left corner before removing the drive completely.

Passo 7  ¶ 

  • The optical drive is still connected by a cable on its bottom side, lift the drive upwards only slightly when first removing from the casing.

  • Pull the optical drive toward the interior of the device and then lift upwards, then pull to remove the cord on the bottom left corner before removing the drive completely.

Passo 8  ¶ 

Unplug connectors at M1, M4, M7, M8, M9 by gently pulling upward. Remove all 3/8 inch Phillips screws connecting motherboard to casing.

Passo 8  ¶ 

  • Unplug connectors at M1, M4, M7, M8, M9 by gently pulling upward.

  • Remove all 3/8 inch Phillips screws connecting motherboard to casing.

Passo 9  ¶ 

Remove the five 1/4 inch Phillips screws and two 1/8 inch Phillips screws on the back of the casing.

Passo 9  ¶ 

  • Remove the five 1/4 inch Phillips screws and two 1/8 inch Phillips screws on the back of the casing.

  • Unscrew and remove nut from threaded connector.

Passo 10  ¶ 

Remove four 1/2 inch screws using a nutdriver.

Passo 10  ¶ 

  • Remove four 1/2 inch screws using a nutdriver.

Passo 11  ¶ 

Pinch the securing tabs and lift the motherboard toward the interior of the device to remove it.

Passo 11  ¶ 

  • Pinch the securing tabs and lift the motherboard toward the interior of the device to remove it.

Passo 12  ¶ 

Pull it toward the interior of the device and lift it away.

Passo 12  ¶ 

  • Pull it toward the interior of the device and lift it away.